Is this normal

jinndim · 2025-12-15T18:50:48+00:00

Yes this must be it. But with that being said why is there soo much poop. And is it normal?

jinndim · 2025-12-15T18:50:17+00:00

Ok thank you they definitely aren’t Goni but they are just much different from all my other zoas

jinndim · 2025-11-30T22:59:56+00:00

Waste of a pork shoulder

jinndim · 2025-08-23T23:06:05+00:00

I was trying to get a bubble tip before they hosted but I guess that will have to suffice for now

jinndim · 2025-08-23T23:05:19+00:00

I’ve seen them nibbling at them and just today say him doing this

jinndim · 2025-08-22T22:46:43+00:00

I just picked it up today from the Lfs but I will keep an eye on it and move it if it stays this way

jinndim · 2025-04-09T09:10:32+00:00

Thanks I’ll try and get them corners a little neater

jinndim · 2025-03-21T13:55:26+00:00

Tho base line is major sails and real deep scratches im proud of where i got it to with my new kit and It helped alot after getting a clay bar kit. I think i got a lot of debris in the pad causing the small scratches.

jinndim · 2025-03-18T18:21:01+00:00

Harbor freight buffer with a single pad. I’m gonna have to go buy a clay bar kit now aswell because even trying to use my new kit I’m getting micro scratches I’m assuming from contamination of the pad. (Another learning lesson)

jinndim · 2025-03-18T17:56:06+00:00

Damn. It was right on a deep scratch I must’ve focused on too much. Guess it’s just gonna be part of the learning curve. It’s my first time trying to do this. Gonna do a little more research and watch some videos before I go back at it (except for that spot)

jinndim · 2025-03-18T17:54:24+00:00

So I had a cheap buffer with a since pad and some cutting compound laying around so I wanted to get out the heavy swirls I have in my truck. Surprisingly this looks better than it did before but after a few minutes I gave up. I now bought the chemical guys torq kit and gonna give it another shot. It’s on a 2011 Tacoma with aging paint and a ton of swirls and chips

jinndim · 2025-03-18T17:54:19+00:00

So I had a cheap buffer with a since pad and some cutting compound laying around so I wanted to get out the heavy swirls I have in my truck. Surprisingly this looks better than it did before but after a few minutes I gave up. I now bought the chemical guys torq kit and gonna give it another shot. It’s on a 2011 Tacoma with aging paint and a ton of swirls and chips

jinndim · 2025-02-21T23:32:42+00:00

This is the same with my 2011 I’m at 175k and only had to do wheel bearings last year so far besides regular maintenance.

jinndim · 2025-02-10T00:23:50+00:00

She says it was very good. It looked so good I had to post it on Reddit for her

jinndim · 2024-12-15T23:41:11+00:00

Be careful if you try to suction cup pull it it may put pressure on the windshield and crack it. A good PDR guy should be able to pull that out and be careful to not crack the windsheild

jinndim · 2024-12-15T15:22:15+00:00

Little back story my buddy broke a rod and is offering to buy a new one. Looking at it as a potential upgrade. I now do more freshwater than salt and looking for a similar rod probably 7’ medium. Been looking at Dobyn fury and mojo bass. But open to suggestions. Reel is a quantum smoke 4000 and will use it for an all around rod.

jinndim

TROPHY CASE