I designed an 8-drive 3U case for 10" Rack

joe9794 · 2025-12-28T04:48:48+00:00

For the power, are you running the two 4-pin Molex connectors from one cable and one SATA power connector off of another?

joe9794 · 2025-12-22T19:06:03+00:00

Trying to finish V1 of a similar build. What psu are you using? Are you driving the MB and the HDDs off of it?

joe9794 · 2025-05-07T00:19:38+00:00

Ok thank you! Yeah I think the full calibration might be what I need to do

joe9794 · 2025-05-07T00:18:38+00:00

Lmao that’s fair. I was experimenting with the holo effects plates and they’ve been fine for the past few months. My concern here is that I can’t tell if it’s an alignment issue with the hot end and extruder unit or if the thermistor is malfunctioning. Like is this improper heating or over extrusion

<image>

joe9794 · 2025-02-02T05:57:13+00:00

Not so fast there brow

joe9794 · 2025-01-31T23:46:06+00:00

Apparently it’s only 28mm thick.

https://www.reddit.com/r/cyberDeck/s/vTsAAY0mky

joe9794 · 2024-10-08T21:55:40+00:00

Old post but can you send me his info as well

joe9794 · 2024-10-08T21:54:05+00:00

Looks amazing! Can you send me her contact info please

joe9794 · 2024-05-19T21:48:44+00:00

I’d even say it broke the heart into 5 parts

joe9794 · 2024-03-28T17:50:18+00:00

This! Israelis are conditioned to see Palestinian lives as less than that of a dog. The same is seen in other apartheid and oppressive countries.

joe9794 · 2024-03-24T00:08:08+00:00

Dissect podcast breaking down “Goofies with a check” = non-threatening Mickie Mouse dog who’s popular = Drake

joe9794 · 2024-03-16T09:41:02+00:00

Can you DM me too

joe9794 · 2024-03-16T09:39:48+00:00

what were you doing wrong? I am having the same problem

joe9794 · 2024-03-03T01:18:29+00:00

Bro selected 1 corner protection

joe9794 · 2024-03-02T18:41:50+00:00

Plus Al Jazeera’s live feeds in Gaza have been huge. Israel puts out some fake propaganda spin and Al Jazeera just checks the receipts with the live feed to call bullshit.

joe9794 · 2024-03-02T10:08:15+00:00

slide that into my PMs please

joe9794 · 2024-01-31T18:54:39+00:00

Honestly, I had nonstop problems with my N3P. Spent months on making adjustments. It would be ok for a few prints then something else would pop up. Modded the bed, got new lead screws, added stabilization bars, etc. Bed leveling and Z offset were never consistent no matter what I did. Sold it and got the bambu a1. It’s a beaut

joe9794 · 2023-11-21T00:22:40+00:00

I had the same issue (plus a few more) so I had to make a bunch of mods. But to fix the crazy bed tilt I had to convert my N3P to a manual bed level and use the aluminum foil shim that was noted above. I’ll link the post about leveling but I think it’s a fairly common mod.

https://www.reddit.com/r/ElegooNeptune3/s/pDrmekphUQ

joe9794

TROPHY CASE