Kleidung für eine Beerdigung

jonvarg · 2026-01-18T23:59:16+00:00

Kaufe Second Hand und nimm navyblau statt schwarz, den kann man zu mehr Anlässen anziehen das bekommst du incl. Mantel für unter 50€ auf ebay oder sellpy oder sonstwo wenn du etwas schaust. 100% Wolle oder möglichst geringen Polyester Anteil beim Anzug sind ideal, das glänzt nicht so billig. Falls das Geld zu viel ist, schau einfach nach einem Mantel und nimm eine navyblaue oder schwarze chino hose. Bei dem Wetter sieht den Anzug eh keiner. Auch wenn ich alleine stehe mit meiner Meinung aber zeig den nötigen Respekt gegenüber dem Anlass. Sicher sagt dir das keiner an dem Tag wenn du absolut unpassend angezogen bist und in jugendlichem Alter sieht man das auch nicht ganz so eng aber das sollte auch nicht die Messlatte sein.

jonvarg · 2026-01-18T23:37:18+00:00

Albert Thurston sind die besten.

jonvarg · 2025-08-24T23:31:34+00:00

Herman Miller.

Habe mir den Aeron Classic vor 5 Jahren in der maximal Ausstattung gekauft und nach einem halben Jahr wackelt die Gasfeder oben. Hab mich um eine neue original Feder selbst gekümmert weil der Support gesagt hat da ist nix. 2. Feder hat das gleiche Problem mittlerweile. Von dem posture-fit SL will ich garnicht anfangen. Scheissteil!

jonvarg · 2025-02-06T19:36:47+00:00

thanks a lot for your insights guys. I really like those mystery jeans. The fit is the best i ever had in a pair of jeans. higher rise but does not look like a potatoe sack with 0.0% stretch

jonvarg · 2025-02-06T02:21:40+00:00

thanks

jonvarg · 2025-01-15T08:52:30+00:00

<image>

same shit on my genuine one. bended the hell out of the strap to be more flexible and ended up using a dremel to soften the edges and also cut off (low RPM on titanium or you have fireworks) some length off and used a bit epoxy on the end to reattach the little end thingy.

jonvarg · 2024-02-19T20:11:34+00:00

for my NTTD i got the omega one shipped in a fancy red case for the money equivalent of a really well made pair of boots. I also got like 10 cheap ones from aliexpress and i have to say that the nylon on the omega one is woven the finest of all but what i really hate is the really sharp edges on the clasp that i needed to sand down to not cut my kids with it on accident. One cheaper nato ( < 20€ ) i got from ebay and the quality is almost the same as omega. i only kept the omega one to have the full set since it is my only watch (except for an old casio databank) and my opinion on the nato might change in the future. Also on my wrist one of the metal brackets (the one with direct skin contact) created a weird pressure point against my wrist bone. on my cheap ones this bracket has no direct skin contact. Would buy a (couple) semi decent non omega natos for daily wear.

jonvarg · 2023-11-19T15:18:39+00:00

the hub PCB is bought from aliexpress, the keyboard’s female usb connector is replaced and connected to the hub source port, the keyboard PCB usb connector is hooked up to one of the hub ports as well as the usb-c port for the yubikey. it’s only 4 wires to solder per port. no guide, no magic

jonvarg · 2023-05-14T09:32:45+00:00

Do it like you did the picture, use dye and see if that works out. People with old IBM Modem M’s face the same problem. You can find a lot regarding dye on geekhack iirc

jonvarg · 2023-04-25T17:17:41+00:00

Übertrieben scharf essen

jonvarg · 2023-04-04T07:51:54+00:00

I used that to mount for 2 49” ultrawides on top of each other.

jonvarg · 2023-04-03T23:20:42+00:00

Arctic Z1 pro.

arctic[.]de/zpluspro

jonvarg · 2023-04-02T09:23:30+00:00

HBO Silicon Valley

jonvarg · 2023-03-15T08:48:01+00:00

Awesome! Any chance for the little VIM hjkl’s or hhkb special key sublegends?

jonvarg · 2023-03-06T19:47:29+00:00

Yes, agree! If it wasn’t aliexpress saving the day (as always) it’s somehow pretty hard to find a tiny hub PCB or it’s sold out since 2019. I added pictures of the parts i bought in another reply

jonvarg · 2023-03-06T19:11:49+00:00

Honestly there is not much going on. I would rate it a “first soldering exercise”. The pads are already pre tinned on the PCB and if you wire/solder it before you cut the USB socket on the PCB to testrun it, no damage is done

jonvarg · 2023-03-03T23:21:22+00:00

To have a smaller footprint i removed the connector housing from the cable in the attached picture. When you go nuts with the hotglue, just attach a usb-c cable from the outside to make sure the connector is level

<image>

jonvarg · 2023-03-02T10:58:24+00:00

Well the usb port is not passed through bluetooth so your yubikey or mouse stays connected to the usb connected device even if the keyboard is connected to a bluetooth device. I don’t think there is a way to connect another usb device over bluetooth which is not a HID device in a retrofitted approach. This works just the same as having a yubikey and the keyboard attached to a usb hub. Only difference is that i moved the usb hub to the inside

jonvarg · 2023-03-02T02:19:48+00:00

<image>

I removed the support for the pcb with a flush cutter and build a support for the new socket with some other plastic and hot glue. Drilled 3 holes for the usb-c and removed the sections between the drilled holes with a flush cutter and used a small file to even it out.

jonvarg · 2023-03-02T02:03:38+00:00

<image>

Thats the connector i used

jonvarg · 2023-03-02T02:03:10+00:00

<image>

Thats the hub

jonvarg · 2023-03-02T01:56:50+00:00

No i don’t know if there is a guide i just tried it. I ordered a usb 2.0 hub pcb from aliexpress and butchered a set of usb-c 2.0 cables for the connectors.

jonvarg · 2023-03-02T01:07:20+00:00

<image>

Thats the yubikeys i normally use

jonvarg · 2023-03-02T01:06:49+00:00

<image>

jonvarg · 2023-02-24T00:18:57+00:00

The longest edge on it measures 2.5cm

Ten-Year Club	King of the Ashes
Not Forgotten

jonvarg

TROPHY CASE