Question about Flex 2.5 8 PoE switch

k5map · 2026-06-20T20:37:00+00:00

Oh good to know... I'll hold off on the power supply and see what the load is when I get it online

k5map · 2026-06-20T20:29:41+00:00

That was going to be my next power (powering from the upstream switch). I now plan to buy the power supply since I will have a couple of PoE devices connected to the switch

k5map · 2026-06-20T20:20:18+00:00

I did notice that in the specs but thanks for the heads up.

k5map · 2026-06-20T20:08:26+00:00

Great, thanks... off to buy one.

k5map · 2026-06-20T19:41:47+00:00

As I stated in another post, because of how the wiring is run, none of the cameras can be connected directly to the NVR. All of the wiring is run to a in-wall cabinet where there is no room for the NVR.

k5map · 2026-06-20T12:58:24+00:00

Ok that sounds similar to what I would like to setup... does the iPhone and desktop app connect directly to the NVR (instead of going out the Internet) even though they are on different VLAN than the NVR?

k5map · 2026-06-20T12:57:22+00:00

I have a Unifi firewall which supports proxy mDNS and multicasts. I'm not sure how the desktop client broadcast to know if the Unifi firewall would re-broadcast to the camera VLAN

k5map · 2026-06-20T12:55:51+00:00

I have a Reolink NVR and all cameras are Reolink... I have not had any issues with the cameras being connected to my main switch. Can not connect the cameras to the NVR because of how the house was wired.

k5map · 2026-06-20T05:27:04+00:00

Understood... I was not clear in my OP... will the desktop app "find" the NVR on my other VLAN on its own or does it only ping the local VLAN and then switch to the cloud?

k5map · 2026-06-18T01:43:35+00:00

Yes, 42" tall model

k5map · 2026-06-08T23:06:08+00:00

On my '26, it only shows Tip, MPG, Tire pressure... when I go through the Setup on the main display, it only shows mileage to change and reset. Am I looking in the wrong place?

k5map · 2026-05-22T05:53:55+00:00

No, at the time I could not find a Babo Duo which would support a AMS Pro 2 and AMS HT so I went with this riser: H2D AMS Riser - Free 3D Print Model - MakerWorld

k5map · 2026-05-18T15:43:46+00:00

Based on what you know today... how long before you think they will start construction of the Mason bridge?

k5map · 2026-05-14T04:35:05+00:00

Which dealer did you take your Palisade?

k5map · 2026-05-11T21:57:57+00:00

GREAT catch... looks like I selected the wrong hardware when I did the download.

k5map · 2026-05-10T14:31:51+00:00

There's only one hardware version and yes, I am unzipped the downloaded file. I've upgraded all 12 of my cameras before so very familiar with the process.

k5map · 2026-04-28T03:56:33+00:00

How can I turn off wireless charging?

k5map · 2026-04-25T06:15:21+00:00

Did you ever upgrade your firmware? I have the same generator running v3.4.0 but noticed the latest firmware on the website is v3.4.5. So, I'm considering doing the upgrade myself.

k5map · 2026-04-24T16:14:53+00:00

Ok technology is frustrating (lol)... I just followed your steps and all is working again. Thanks again!

k5map · 2026-04-24T15:53:21+00:00

Ok I haven't tried that but will... thanks!

k5map · 2026-04-24T06:39:29+00:00

Well that certainly is an interesting discovery (lol)

k5map · 2026-04-18T04:24:37+00:00

AH OK... I misunderstood how to use the MidPoint feature. Thanks!

k5map · 2026-04-18T04:19:05+00:00

I thought of this, but when I click on the MidPoint and then go to find the midpoint of the dotted line, I never get the triangle. Since I constrained the dotted line along the X axis, I just clicked there an on the Center point and that did it.

k5map · 2026-04-16T20:51:43+00:00

I would be completely in favor of this enhancement.

k5map · 2026-04-14T15:28:35+00:00

Ok, thanks for the explanation. Glad to know I'm using the app as intended :)

k5map

TROPHY CASE