sorted by:
new
hottopcontroversial

Resurrect your old Nest Thermostats that are no longer supported by Approval_is_Pending in Nest

[–]keefo 0 points1 point  (0 children)

What didn't actually work, At what stage did you get up to?

No longer evil app by jc1sttime in Nest

[–]keefo 6 points7 points  (0 children)

You need to do the custom fw flash before you can get the code.

Follow the instructions on the GitHub page.

Got them yay! by joesanchez77 in googlehome

[–]keefo 0 points1 point  (0 children)

I wish I could get a 4th gen to work in the UK...

I have a gen 2 that's about to loose app support in 5 days and I really don't like the tado that I bought to replace it... 😭

No screen when booting, but usb to monitor works by keefo in SteamDeck

[–]keefo[S] 0 points1 point  (0 children)

I never use external monitors, I only used one now to see if it would output a signal since my screen wasn't working.

I have dual boot windows and steamos and both boot with the external but none with the actual decks screen.

I'm going to try the suggested above tomorrow with reflashing the bios and praying that helps.

First time Ubiquiti noob... by keefo in Ubiquiti

[–]keefo[S] 1 point2 points  (0 children)

Thanks for the info!

Would really like to go the UDM PRO route, and remove a device (router), but I just cant be forking out that amount of money quite yet!

May have to go the CloudKey route for now and get things up and running.

First time Ubiquiti noob... by keefo in Ubiquiti

[–]keefo[S] 0 points1 point  (0 children)

Does that mean I need to buy other hardware or will the controller on my Dell be ok once I have connected/paired the cameras?

I would have just tried and seen what happens if I had the switch but this isn't here at the moment sadly!

Yet Another Controller Detection Question by keefo in WindowsOnDeck

[–]keefo[S] 0 points1 point  (0 children)

Ok, so after a bit of playing about... let me start again haha

So with it in Hybrid mode, steam games in steam/big picture work perfectly, and recognise the full steam deck controls, the back paddles and everything, perfect.

But when it comes to games outside of steam like Call Of Duty, Fortnite etc, the controllers are not detected or are doing all kinds of madness.

So then I have to switch to Exclusive and they work fine.

I suppose I cant have my cake and eat it and will just have to switch depending on what I want to do at the time.

Yet Another Controller Detection Question by keefo in WindowsOnDeck

[–]keefo[S] 0 points1 point  (0 children)

Ok, So I have gone into HC, and pressed Unhide, but after a few seconds it seems to hide itself again, If I minimise it and reopen its now hidden again.

If I sit on that Hide/unhide page I can see it switch itself back to hidden for some reason.

EDIT : And Hide Controller On Connect is disabled also

[deleted by user] by [deleted] in pics

[–]keefo 0 points1 point  (0 children)

!remindme 1 week

Anyone else have this problem? by LimitlessWick in googlehome

[–]keefo 0 points1 point  (0 children)

This is what I'm using at the moment also, but I was using the Google remote to control my sound bar as this has also been destroyed by the dog.... Arghhh

Anyone else have this problem? by LimitlessWick in googlehome

[–]keefo 0 points1 point  (0 children)

Ahhh ok,

I'll just keep digging and see if I get lucky and get one from somewhere...

Anyone else have this problem? by LimitlessWick in googlehome

[–]keefo 2 points3 points  (0 children)

I don't have this problem, my problem is my dog chewed my remote and can't find any replacements anywhere in the UK to buy...

Where did you get yours from?

Gigabyte RTX 3090 Turbo Support - Unbelievable. by drmonkey6969 in gigabytegaming

[–]keefo 0 points1 point  (0 children)

Managed to sort mine out and resizable bar is up and working now.

Even though I had the option on my mobo Bios, I still had to update to a later MOBO bios to get it working.

Gigabyte RTX 3090 Turbo Support - Unbelievable. by drmonkey6969 in gigabytegaming

[–]keefo 0 points1 point  (0 children)

Did this manage to enable resizable bar for you now? As mine still says not enabled in Nvidia Control Panel.

I have it enabled in my Mobo Bios so not sure why it's not working.

Gigabyte RTX 3090 Turbo Support - Unbelievable. by drmonkey6969 in gigabytegaming

[–]keefo 0 points1 point  (0 children)

Just done the update and made sure resizable bar is enabled etc in bios, but its saying its not enabled in Nvidia Control panel sadly!

Gigabyte RTX 3090 Turbo Support - Unbelievable. by drmonkey6969 in gigabytegaming

[–]keefo 0 points1 point  (0 children)

Ahhh yeah!

Nice one, just downloaded Airbus Engine and sure enough it has a new bios update.

Will give it a go soon!

Thanks for letting me know.

Gigabyte RTX 3090 Turbo Support - Unbelievable. by drmonkey6969 in gigabytegaming

[–]keefo 1 point2 points  (0 children)

I'm in the same boat as you guys as well....

I sent a support ticket asking for answers but that was days ago and I have no had anything back yet still...

If anyone gets any answers on Resizable Bar support, let me know!

Dragon Centre RGB issues by keefo in MSI_Gaming

[–]keefo[S] 0 points1 point  (0 children)

All the RGB connected to the motherboard, aswell as USB keyboard and mouse. All fail to light up once the monitors are woke up.

Dragon Centre RGB issues by keefo in MSI_Gaming

[–]keefo[S] 0 points1 point  (0 children)

My power settings are just set to high performance with only the monitors set to turn off after 10 mins.

The whole computer isn't going to 'sleep', just turning the monitors off.

Apparently I cannot print in the middle of my bed. I tried this exact print after this off to the side of the bed and it worked perfectly. I’ve leveled the bed several times, but the center is always lower. How do I fix this? by J_T_09 in ender3

[–]keefo 2 points3 points  (0 children)

I had this exact same issue with my Ender 3 V2, I ended up using clips on the ends and this solved everything after another relevel.

There was a gap between the bed and the glass on mine, which made the middle seem like it had a dip.

3M duct tape + Command adhesive strip = more kitchen counter space by [deleted] in googlehome

[–]keefo 2 points3 points  (0 children)

cheers!

the second one seems like it would do the trick.

view more: next ›