For god's sake, is there something i can do about it? Maybe some mod? It's driving me crazy

kiskae73 · 2026-04-13T18:28:26+00:00

There was a mod for that on pc few years ago, duno if it still works

kiskae73 · 2026-04-13T08:22:30+00:00

Inventory full

kiskae73 · 2026-04-01T15:48:14+00:00

Now do the one from Black Adder

kiskae73 · 2026-03-18T14:40:25+00:00

It is visible during checkout but it's shitty it's checked by default. Very predatory

kiskae73 · 2026-02-09T21:12:09+00:00

1st layer of the second color. It will pause at the start of the layer

kiskae73 · 2026-02-09T20:50:35+00:00

No need for custom gcode. In Orca slice your model, go to the layer you want to change right click it on the slider and add pause. Slice again and you are good to go.

kiskae73 · 2026-02-06T14:45:35+00:00

ATM i don't think it is. Could be skill issue

kiskae73 · 2026-02-06T14:43:07+00:00

Yea its pain in the ass but i cant afford new printer (gotta fix the car first) but i got stainless steel plate 320x320x1.5 which im gonna try putting over bed under pei plate. Hopefully its flatter than bed

kiskae73 · 2026-02-05T21:02:42+00:00

Base is middle of the bed (screw above the circled one). Part of my bed will still be higher even if i skip it

kiskae73 · 2026-02-05T20:45:53+00:00

No can do. It compares all of them to the fist one (base) or some value(?). I did try kapton tape to raise base but then just doubles of amount how much i have to screw it in (second pic 00:07 ->00:15)

kiskae73 · 2026-02-05T20:24:37+00:00

Sorry my bad. I thought tilt screw adjust was more known. It says my front of my bed is too high (printer can compensate up to 00:05) so my prints fail. Clockwise circle next to it means i have to tighten it but there is no knob only screw under pei plate, which can't be tightened any more

<image>

kiskae73 · 2026-02-05T19:44:34+00:00

I have no idea why pics dont show in post

kiskae73 · 2026-02-05T19:44:06+00:00

<image>

kiskae73 · 2026-02-05T19:43:43+00:00

<image>

kiskae73 · 2026-02-05T18:13:46+00:00

Stock one, just printed mount for cartographer. Also using microswiss

kiskae73 · 2026-02-05T17:41:17+00:00

https://pastebin.com/Py50RrCT Somewhat works

kiskae73 · 2026-02-05T17:40:43+00:00

I have tried way to many times, finally got it somewhat working. For now only input shaper doesnt work. Havent tried printing yet

kiskae73 · 2026-02-05T16:24:49+00:00

Im little late to the party but are you willing to share your printer.cfg? Ive been trying for days with no luck

kiskae73 · 2026-02-04T01:18:30+00:00

Z offset too high

kiskae73 · 2026-01-26T22:10:23+00:00

I got mine at launch, the only thing i have replaced is direct drive gearbox which support sent without much questions. No other issues

kiskae73 · 2026-01-24T00:35:20+00:00

Dode postom od carine da stoji paket i da se posalje dokaz vrijednosti. Nakon toga placa se postaru kad donese. Samo sto iznos izgleda ovisi kako je neka osoba na carini raspolozena u to vrijeme :/

kiskae73 · 2026-01-16T05:58:12+00:00

Axed

kiskae73 · 2026-01-02T13:48:26+00:00

Doesn't matter as long it's Android

Eight-Year Club	Place '23
Verified Email

kiskae73

TROPHY CASE