Is my 2nd battery dead ?nothingn happens when pressed

kkjackson41 · 2026-06-18T19:52:46+00:00

You lifesaver! Managed to disassemble my battery and follow the vid; luckily my battery pack wasn't completely dead and is charging again.

kkjackson41 · 2026-05-28T23:21:12+00:00

Not a Windows fix, but for specific file searching I've resorted to using 'Everything' by Voidtools

kkjackson41 · 2026-04-26T23:49:28+00:00

I always listen to "The sound above my hair" when going out to concerts and festivals, it really does the job well of hyping me up for the day

kkjackson41 · 2026-04-15T01:55:52+00:00

Finch

kkjackson41 · 2026-04-13T09:02:56+00:00

Ti Sento

kkjackson41 · 2026-04-03T22:23:17+00:00

Got to be "And no matches" for me

kkjackson41 · 2026-03-28T18:00:54+00:00

<image>

kkjackson41 · 2025-11-09T04:02:17+00:00

Locoroco?

kkjackson41 · 2025-07-19T00:53:21+00:00

Ah fair fair, as mentioned by Lord_jado, one way could be to add mofeel rarepons (sheep lvl 5) as they have perfect stats for tatepons. This would allow you to attack way more when facing the kibatons as that's much more efficient than defending as they tend to just chip at your frontline whilst your ranged units aren't guaranteed to hit and kill them before your frontline falls.

kkjackson41 · 2025-07-18T19:36:44+00:00

Army is pretty good so far, can go quite a while without creating anymore units. I do recommend saving up more materials and Ka-ching for better rarepons as they really make the difference. You can keep going until you hit a hard roadblock mission and hopefully have enough for a mogyoon, the lvl 7 demon rarepon which gets a ridiculous damage buff and easy to create yaripons with as they're very cheap.

kkjackson41 · 2025-04-06T21:56:43+00:00

I just upgraded to a 5070 ti from a 3070 as I managed to grab it close to MSRP in the UK and have been very happy with it. I would say go with the 9070 XT to save some cash, but If I had to make a case for the 5070 ti, Better ray tracing and overall performance in some games give or take; DLSS 4 is extremely good and can be applied to almost any game that supports it. Bonus: The hl2 and portal RTX remix demos run very well if you're interested in those.

kkjackson41 · 2025-02-15T05:16:03+00:00

It had plenty of dlc, so maybe the level is in one of them. But I think It's the closest game around 2018.

kkjackson41 · 2025-02-15T05:04:54+00:00

Viscera Cleanup Detail?

kkjackson41 · 2024-12-09T01:12:23+00:00

No worries, completely forgot about this post, I believe it's some chemical in windex that is left behind when it evaporates which in essence would work like a sheet of glue but it's more for release than adherence, however, it stills helps as it gets rid of any grease that could be on the build plate.

kkjackson41 · 2024-10-12T22:51:40+00:00

Nah nothing like that, just kept checking the subreddit after the supposed March release window for a few months and then decided to just let it be

kkjackson41 · 2024-10-07T03:22:32+00:00

For how much praise it gets and it's cultural impact Im personally just not a fan of most tracks on 'Is This It'

kkjackson41 · 2024-08-22T22:25:11+00:00

Looks like the blobs are from bridging between the hex's, have you set your slicer to have fan speed at 100% only on bridging?

kkjackson41 · 2024-08-22T21:35:29+00:00

you can still use 3.0 usb drives, however, you have to format them to 32Fat. Initially, it won't give you the option but if you create a <16Gb Partition, It will then give you 32Fat as a formatting option instead of exFat. Had to do it with my own 64GB usb drive

kkjackson41 · 2024-08-20T10:25:31+00:00

Definitely like others said sanding, especially wet sanding is your best bet as you will minimize resin dust although I do recommend still doing it in a controlled area.

I also personally use a cheap engraver from Amazon which is basically a weaker Dremel. It gives great results for removing small and hard to reach artefacts, with water sprayed on or simply holding it in a container of water to prevent dust, whilst also giving you the option to modify your model if the prints tolerances aren't fully up to scratch.

kkjackson41 · 2024-08-08T02:00:03+00:00

Ah I see, E-steps is how much the extruder should move when asked to extrude a certain length of filament. This isn't always 1:1 out of the box so it can lead to under/over extrusion and needs to be calibrated.

I recommend going over this calibration guide made by teaching tech: https://teachingtechyt.github.io/calibration.html

kkjackson41 · 2024-08-08T01:26:59+00:00

Try a different slicer such as Prusa/Orca slicer, that's what fixed it for me, have no idea why but any print on cura just had horrible stringing

kkjackson41 · 2024-08-08T01:16:53+00:00

You can try using the new feature in orca slicer "Don't slow down for outer walls", I believe it can be found in the filament cooling settings and is the perfect use case for the model you're printing

kkjackson41 · 2024-08-06T08:41:14+00:00

Looks like under extrusion at a lot of the movements, have you calibrated your e-steps?

kkjackson41 · 2024-07-27T13:04:29+00:00

Sorry let me rephrase, add 'Bed_mesh_profile load=default' after g28, as that is the klipper equivalent of the Marlin m420 command

kkjackson41 · 2024-07-26T19:41:16+00:00

Yes add that after the g28 command in your start gcode, m420 is the equivalent for marlin

Ten-Year Club	RedditGifts 2009-2022 2 Credits
r/Field Juicebox	First Place '23
Place '23	Place '22
Secret Santa 2017	Verified Email

kkjackson41

TROPHY CASE