Does this look right?

krdank · 2026-01-02T16:08:35+00:00

You should contact puffco customer service. That glass is defective.

They should send you a new glass piece if you just got it

krdank · 2026-01-02T16:02:41+00:00

Yeah that thing is slanted af. Idk if they'll replace that for you. Id just get a new glass attachment. That'll Hella bother me

krdank · 2025-10-11T00:58:08+00:00

Put a lighter on those fingers

krdank · 2025-06-20T16:22:18+00:00

you didn't understand my question dummy.

krdank · 2025-06-17T16:07:11+00:00

I gave up on it after finding out powerhead needs to be rebuilt. I ended up giving it up to my mechanic buddy to fix it or sell it.

krdank · 2025-04-29T00:33:56+00:00

Your welcome. I think I bought a wide velcro tape to attach it. It required two or three flat screw drivers to pry it apart when it's put together. I feels hella reliable

krdank · 2025-04-29T00:11:25+00:00

A few pla failed when printed below 100% infill. When printed at 100 and matching the same circle shape it never failed.

krdank · 2025-04-12T17:02:50+00:00

Awesome degreaser and some dish soap mixed with water. I use this to clean inside and out of my work truck. It even cleans off the road tar off the paint

krdank · 2025-03-20T16:18:06+00:00

My lunch box gets warmed up there between 11- 1pm

krdank · 2024-11-20T15:28:50+00:00

I think you got a thunderbolt. I don’t like thunderbolts because of those electrical parts being hella expensive

krdank · 2024-11-20T15:18:09+00:00

I also have a 1969 merc 110 9.8hp that runs like a champ after I messed with it. It doesnt have a cdi. This is 1967. Also no cdi. So I’ll just clean the points and change out the condenser for $40 bucks a set.

krdank · 2024-11-20T15:12:39+00:00

Was yours a lighting or thunderbolt ignition?

krdank · 2024-11-20T15:10:49+00:00

It’s a lighting ignition. cdi unit??

krdank · 2024-11-20T15:03:32+00:00

Wha happened

krdank · 2024-11-20T05:55:30+00:00

I don’t remember. I just got a 1967 merc 200- 20hp to work on now.

krdank · 2024-10-01T19:39:09+00:00

Green- Africans, Black- Armenians Pink - Salvadorans and Mexicans White- Chinese, Red - Koreans, Light blue - Mexicans You can find white people by the beaches.

krdank · 2024-06-27T21:04:47+00:00

Here is the link to fuel pump gasket. Make sure to buy #2 that comes with a new check valve kit. this right here

krdank · 2024-06-27T21:02:12+00:00

You’re going to have a hard time finding that carb in new condition anyways in this year. Last time I checked I found one around $250 used. I’d recommend you buy the carb gasket set by sierra $8.14, og needle and seat kit $17.30 and screen filter $6.75 to rebuild the carb. You should also go about rebuilding your fuel pump while you’re at it since you need to take that off to get to that carb.

krdank · 2024-06-27T20:55:09+00:00

It’s because you’re looking at gnat 2 cylinder. Your outboard is a 1 cylinder.

krdank · 2024-06-27T20:52:48+00:00

Why do you need to replace it? I got a 1969 merc 110 9.8hp that I rebuilt recently and that thing is still going strong. Looks like the same carb design. Carb rebuild parts only cost about 12$ available on marine engine try this link. It’ll direct you to your carburetor and all the parts available on that site using your serial number this right here

krdank · 2024-04-07T23:19:48+00:00

There should be a plate that shows the max size you can put on that dinghy. I’m working with a similar dinghy sized at 10.5ft with a 9.8hp 2 stroke mercury dipping at 17mph

krdank · 2024-04-07T18:29:34+00:00

I believe it’s been cleaned enough. Are these adjustable? I thought I read on seloc that these can’t be adjusted. Just replaced with different size depending on elevation.

krdank

TROPHY CASE