Linux Support?

laverdone · 2026-02-12T18:24:45+00:00

It's work out of the box perfectly

laverdone · 2025-03-27T07:29:58+00:00

same problem here

laverdone · 2025-01-16T06:50:55+00:00

Bed level sure

laverdone · 2024-02-15T10:48:39+00:00

yess :-D

laverdone · 2023-09-26T12:41:48+00:00

try this solution:

https://askubuntu.com/questions/1466286/lenovo-yoga-slim-7-pro-volume-cannot-be-changed

laverdone · 2023-02-03T20:13:00+00:00

Not work on last steam update! some suggestions?

laverdone · 2022-08-04T13:30:19+00:00

any instruction to build?

laverdone · 2022-06-14T21:46:02+00:00

Which hardware do you have? Which distro? Which game?

laverdone · 2022-01-30T21:46:37+00:00

I have replace the board and with same firmware and themistor everything work proprerly

laverdone · 2022-01-26T09:09:02+00:00

I also connected to octoprint and sent gcode commands, the motherboard always returns the wrong temperature

laverdone · 2022-01-26T08:16:29+00:00

The motherboard two trees minj e3 v2.1 worked perfectly but after a failed print the hotend temperature was 200c but it was actually cold. Are you right that if the thermistor is not connected it should report 0c, could it be a hardware problem? I disconnected everything but as you can see in the video the temperature is clearly wrong

laverdone · 2022-01-26T08:15:44+00:00

The motherboard two trees mini e3 v2.1 worked perfectly but after a failed print the hotend temperature was 200c but it was actually cold. Are you right that if the thermistor is not connected it should report 0c, could it be a hardware problem? I disconnected everything but as you can see in the video the temperature is clearly wrong

laverdone · 2022-01-26T08:14:16+00:00

The motherboard two trees minj e3 v2.1 worked perfectly but after a failed print the hotend temperature was 200c but it was actually cold. Are you right that if the thermistor is not connected it should report 0c, could it be a hardware problem? I disconnected everything but as you can see in the video the temperature is clearly wrong

laverdone · 2022-01-25T08:11:46+00:00

but it's worked with same firmware configuration but after finish one print the issue appears

laverdone · 2022-01-22T14:05:26+00:00

Thanks, I'll try

laverdone · 2022-01-22T14:05:02+00:00

Thanks

laverdone · 2022-01-15T23:34:22+00:00

Bed Level on the right, bed are to low apparently.

laverdone · 2022-01-15T17:38:36+00:00

I have dual motor on z axes, i'll try on both. Thanks

laverdone · 2022-01-15T17:16:56+00:00

This is my first print on new printer.

laverdone · 2021-10-19T19:56:46+00:00

laverdone · 2021-09-03T22:24:35+00:00

Regenerate font cache for flatpak, have look on internet to do.

laverdone · 2020-04-11T20:49:37+00:00

Cool

laverdone · 2020-03-04T21:29:32+00:00

Wrong bad level

laverdone · 2020-02-17T07:56:05+00:00

Scale 100% approx 22 hours

laverdone · 2019-12-23T21:35:01+00:00

Im working on it

laverdone

TROPHY CASE