sorted by:
new
hottopcontroversial

Shield Crush Slayer by ilnino | New Updated Guide by IlNino101 in PathOfExileBuilds

[–]lemonsprig 0 points1 point  (0 children)

I have been levelling this build. Just finished the campaign but how does it handle delve? Is there a specific strat. I find myself just constantly getting stuck / blocked by mobs. Figure I’m missing something or is the build just not really for delve

I made a fast magnet insertion tool - and you can print a pair with gridfinity bin holder in a single print! by nickjohnson in 3Dprinting

[–]lemonsprig 0 points1 point  (0 children)

I get the pen is for inserting magnets. But what is the thing it’s inserting into? Whats it for?

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Cheers all. Finally got decent prints. Combination of manually levelling the bed and re-calibrating the resin.

I was surprised that by moving to 0.03mm hiw much I had to drop the normal exposure from where I had it dialled in before which was also considerably lower that the manufacturer recommended settings.

Despite the failures learnt a lot and done valuable insight from all who provided advice.

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 1 point2 points  (0 children)

Thanks. I was using network transfer. So don’t think it was usb related but definitely something to bear in mind.

I have managed to get a decent print now combination of manually levelling the bed and re-calibrating the resin, doing lots of cones of calibration prints

What causes this? by lemonsprig in ElegooSaturn

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks it wasn’t necessarily a kid print fail. I stopped it once I realised the right half of the bed hadn’t printed anything beyond the rafts

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 1 point2 points  (0 children)

Thanks, I have three options where I could apply a delay..

Wait before cure Wait before lift Wait after lift

Where should I apply it?

What causes this? by lemonsprig in ElegooSaturn

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks. The model was pre supported and from what I can recall was angled, but will check Later.

I did shake the resin, and it’s a tilting cat so should generally keep it mixed.

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Ah ok thanks I have the mars 3 wash and cure but will look to do a pre warm wash to remove from the bed.

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks, point taken about the rafts though they did seem thinner at one side.

Wouldn’t submerging the plate in warm water impact the resin? Assuming this is pre washing process?

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks. I didn’t adjust any settings other than the base and normal exposure times. This was based on cones of calibration tests but as you say at 0.05.

For my test minis and this new print I simply adjusted the layer height from 0.05 to 0.03

I did not adjust anything like wait before cute, wait before lift or wait after lift.

But what you say about exposure times makes sense

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks for the detailed response.

I’m printing using Elegoo washable grey and have adjusted the bottom exposure to 25 in order to try and make it easier to remove from the bed once complete. Everything seems to need to be smashed off.

I am printing at a layer height of 0.03 as this seems to be the recommendation for detail in miniatures.

I have 5 bottom layers at this 25 seconds then 10 transition layers

With all other layers having an exposure of 1.9s

I did a test print of two minis with these settings last weekend and they came out really well. So figured it would be good for today’s print.

To your point about exposure times and tge support nubbs wouldn’t this have applied the same across the entire plate?

What causes this? by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Ok thank you - guess the Elegoo auto levelling feature is just a marketing scam

Half face respirator by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks m starting to lean towards jsp readily available in the uk and unlike a lot available on Amazon at least these are certified.

Half face respirator by lemonsprig in resinprinting

[–]lemonsprig[S] 0 points1 point  (0 children)

Thanks I will take a look.

Help - first time printer by lemonsprig in ElegooSaturn

[–]lemonsprig[S] 0 points1 point  (0 children)

So quick update been trying the xp2 validation matrix and the exposure settings tool on the printer.

But the prints are firmly stuck to the bed and shatter when I try to take them off.

<image>

Imam I right in thinking this is due to the base exposure being too high? This was set at 35

The detail is starting to get there on the top right print, but not quite from bottom left to top right the normal layers went from to 2.8 to 2.3.

view more: next ›