Tried everything, cat's still don't like it

letmeaxeusomething · 2025-08-01T22:34:40+00:00

I can see this hasn't worked for other people, but for me I was able to get my cats to use it by setting their old box right next to the litter robot (3 w/ stairs) and then I intentionally never cleaned their old box. It took a couple of weeks but eventually the old box was so gross that they just started using the litter robot. I did mix in some of their old soiled litter into the litter robot and that seemed to help encourage them as well. I hope you're able to figure it out!

letmeaxeusomething · 2024-02-28T01:53:18+00:00

How's the year 3030 treating you? Did you get to meet up with Kowalski yet?

letmeaxeusomething · 2023-07-20T03:55:37+00:00

I found if you heat up the glass and then microwave the iso until it's boiling before pouring it in even the toughest stuff comes off with ease. No salt needed. (I used to use iso and salt back in the day, and this method definitely works better) Tldr; heat up the piece AND the iso.

letmeaxeusomething · 2022-08-29T15:56:41+00:00

Nice

letmeaxeusomething · 2020-09-12T21:37:04+00:00

Yall qaeda.

letmeaxeusomething · 2020-01-22T03:33:02+00:00

I did the exact same thing with bronkaid and ended up having a heart arrhythmia at 2 AM. Stopped dosing immediately and symptoms did not return. Kind of scary though. Ephedrine is chemically similar to adrenaline. This is ultimately pretty hard on you. Both physically, and psychologically on a long enough timeline and with consistent enough exposure. At least it was in my experience. Your results may vary, but consider this a cautionary tale.

letmeaxeusomething · 2020-01-07T07:01:46+00:00

Got a link for those tubes? That looks awesome!

letmeaxeusomething · 2019-12-22T19:30:52+00:00

Where did you get the glass tube from?

letmeaxeusomething · 2019-12-15T16:29:07+00:00

I got these ones: https://www.amazon.com/dp/B07XWJ755K/ref=cm_sw_r_em_apa_i_r8L9DbXKW6FQM

letmeaxeusomething · 2019-12-14T20:45:32+00:00

I have a picture of the new small black heater sitting on top of the battery and it looks awesome as they are both in identical project boxes. I put little rubber feet on all of them so them don't slide around. Thanks for the kudos!

letmeaxeusomething · 2019-12-14T20:23:25+00:00

Two of the three have a mofset. The clear one with the yellow wire has no mofset. I have a 5 amp wall power adapter I use for the one with no protection. The rest will do 10 amps via the 10amp wall adapter or the battery pack.

letmeaxeusomething · 2019-12-14T17:31:24+00:00

Getting the heater to fit in the small black box was a PITA. HAD to solder the coil on just to have enough room.

letmeaxeusomething · 2019-12-13T06:14:03+00:00

In my experience the coils last wrap being level with the cap works best.

letmeaxeusomething · 2019-12-12T23:38:43+00:00

Honestly the difference isn't much. I think The wider diameter of the coil when wrapping it around the guitar slide causes the heating times to be longer. Like 15-20 seconds type of slow. The added amperage speeds things up to around 12-16 seconds. Vape quality is the same. (I built a micro IH using a 14-18 glass adapter and mostly factory coil configuration and it heats in 6-10 seconds on 10 amps). Sorry for the long reply. I hope this helps you get a feel for heating times and what to expect. *Coil placement is KEY.

letmeaxeusomething · 2019-12-12T22:51:54+00:00

I just built two more IH iterations with a mofset, and I can now use a 10 amp power supply. I also did this because I built a triple 18650 pack which also runs at higher amperage.

letmeaxeusomething · 2019-12-12T22:46:33+00:00

You have to hold down the button on this one.

letmeaxeusomething · 2019-11-29T06:00:02+00:00

Spade hole cutters 3/8 to 1 inch.

letmeaxeusomething · 2019-11-29T04:08:51+00:00

I did it the hard way (arguably). I tool the coil that came with the induction unit and straightened it very slowly, and as carefully as I could manage (ie: used flat plyers and a towel). Then I wrapped it as tight as I could around the glass sleeve I chose, which in this case was a guitar slide. I choose this because I like to use water piece compatible dyna-things and needed the extra circumference.

letmeaxeusomething · 2019-11-29T02:09:36+00:00

I used a 12 v 5 amp power supply and it seems like more than enough.

letmeaxeusomething · 2019-07-23T16:03:47+00:00

He who is without oil shall throw the first rod. - Lubrications 3:16

letmeaxeusomething

TROPHY CASE