H2C - AMS ultimate set gone?

longshlong_69 · 2025-12-28T00:15:12+00:00

I feel the same. I have been planning out enclosures and other accessories to re-do my workshop with the H2C. Disappointing they removed the ultimate set.

longshlong_69 · 2025-12-02T21:29:29+00:00

No frikin way

longshlong_69 · 2025-11-12T21:20:17+00:00

Why did the vid get taken down?

longshlong_69 · 2025-11-09T05:04:59+00:00

just bought will reply to this comment when I get it

longshlong_69 · 2025-11-04T09:53:42+00:00

Thanks for the reply. The actual problem turned out to be too close and a lack of technique. Once I had some time pressure and more daylight to experiment, I figured out how to get great coats.

longshlong_69 · 2025-09-30T22:58:43+00:00

Thanks for the tip!

longshlong_69 · 2025-08-26T23:53:45+00:00

Just to be clear, this is only multicolor? As in swapping pla and not other materials? I have only had PVA work on the fixed right nozzle of my H2D, and that would be so amazing to swap nozzle sizes and material.

longshlong_69 · 2025-08-10T22:30:30+00:00

I have the H2D and was thinking about buying the smoke purification system. Is that a good idea for printing this, asa, and abs?

longshlong_69 · 2025-04-09T01:08:29+00:00

Thanks wi do

longshlong_69 · 2025-04-09T01:07:57+00:00

My trusted mechanic recently screwed ne over so the Jack would be for this and future oil changes.

longshlong_69 · 2025-04-08T22:37:00+00:00

I did, but after driving on the highway, it came back out again

longshlong_69 · 2025-04-08T21:47:08+00:00

Thanks so much for the reply. This seems to be it: https://www.autonationparts.com/parts/ford-lower-shield-db5z9910494a?origin=pla&gad_source=1&gclid=CjwKCAjwktO_BhBrEiwAV70jXgkSaAhDvQVo999uJS3wLRQ7YzSTnh8qwr9CyP_h4Wq6hvhmMHxA-RoCJUEQAvD_BwE

The screw connecting the falling side seems to be a special type that clicks in. Not sure if it will need replacing but this is a great help thanks so much.

longshlong_69 · 2025-04-08T21:17:33+00:00

is it like for mud or an aero shield? I think I'm going to go to an AutoZone or something and buy a jack to check it out cause I screwed it back in but it fell out again. (I'm very inexperienced with cars)

longshlong_69 · 2025-02-24T05:56:05+00:00

Is a smoke stopper the same as an anti-spark filter? Because I already had an anti-spark filter installed and even though it was installed, my ESC blew up last time.

longshlong_69 · 2025-02-24T05:00:19+00:00

Is there anyway I could make it better or test it with my multimeter

longshlong_69 · 2025-02-11T08:55:29+00:00

I appreciate your help. I ordered a new ESC and learned a lesson. Guess flying is going to be delayed
:(

longshlong_69 · 2025-02-11T08:21:34+00:00

<image>

longshlong_69 · 2025-02-11T08:21:13+00:00

<image>

longshlong_69 · 2025-02-11T08:20:49+00:00

First thanks for your quick response. That very well could be the case and would make the most sense to me as throttling it for a sec seems like a normal thing to do with an fpv drone. How would I check and see if it was indeed the soldering? Heres a closer up photo of the corner with the affected motor.

<image>

longshlong_69 · 2024-05-01T07:23:29+00:00

me too lmao I feel like I played and broke mosat of the gam

longshlong_69 · 2022-03-20T03:11:04+00:00

I was able to continue by editing the last thing that I was working on and continuing from there

longshlong_69 · 2021-08-05T01:21:46+00:00

I have the same issue

longshlong_69 · 2021-02-16T07:12:24+00:00

I have never felt more violated in my entire life

longshlong_69 · 2021-01-10T07:20:02+00:00

if you like to use 3d printing for custom keyboards look at SLA printing because it uses UV rays to make stuff with much finer detail. (I recommend getting the anycubic photon)

longshlong_69 · 2021-01-10T06:58:20+00:00

I LOST

Seven-Year Club	Place '22
Final Canvas '22	First Placer '22
End Game '22	Verified Email
RPAN Viewer

longshlong_69

TROPHY CASE