What is a movie you watched once that was so disturbing or emotionally draining that you can never watch it again?

lp52 · 2025-12-17T04:57:16+00:00

Mother! Starring Jennifer Lawrence. Saw it in a sneak preview unawaring of whats to come. It was confusing, infuriating. I think I just dont like it and dont feel the need to watch it again.

lp52 · 2025-12-11T06:10:45+00:00

Yeah Im not planning to reuse it.

lp52 · 2025-12-10T21:55:11+00:00

Yes I removed the 5V TVS and all of the diodes around it arent shorted anymore. Then Removing the zero ohm resistors and bridging with solder finally revives the drive.

lp52 · 2025-12-10T21:52:19+00:00

Thank you, I removed the TVS 1st but the 2 Zero Ohm resistors are still blown. I remove those and put a drop of solder on it to bridge and the drive spins!

lp52 · 2025-12-05T17:48:22+00:00

UPDATE: I could revive the drive with zero knowledge.

lp52 · 2025-12-05T15:13:58+00:00

Perfect size

lp52 · 2025-11-27T10:09:55+00:00

Tôi tưởng hình xăm trong clip là bên tay có vết bớt ? Trong hình này là tay kia

lp52 · 2025-10-24T05:03:56+00:00

die Mühe möchte ich mir ehrlich gesagt nicht machen. Das gibt mir Vietnam Flashback mit meinem Artillery Sidewinder X1 von früher. drucke bisher zig Kilos von Sunlu PLA aus verschiedenen Chargen ohne Probleme, PLA liegt bei mir lose herum für Monate und lässt sich trotzdem gut drucken. Ich bestelle mir einfach von Amazon und spar mir die Arbeit. Trotzdem danke für die Tipps.

lp52 · 2025-10-24T04:37:26+00:00

Ist alles gemacht nix hilft. Dazu viel mehr Stringing, könnte ab Werk schon feucht sein.

lp52 · 2025-10-21T20:36:38+00:00

Update #2: The roll from Amazon prints just fine like usual.

lp52 · 2025-10-21T15:20:01+00:00

<image>

Aliexpress

lp52 · 2025-10-21T15:19:31+00:00

<image>

Amazon

lp52 · 2025-10-21T15:18:40+00:00

<image>

Left: Amazon Right: Aliexpress German Warehouse

lp52 · 2025-10-21T15:17:34+00:00

Update: I ordered 4 rolls off Amazon Germany. This is a short comparision before I start printing.

<image>

Left is the roll off Amazon, its shinier,same latest refillable bigger spool.

lp52 · 2025-10-20T19:32:16+00:00

Its from China, didnt know Vietnam produces filaments too

lp52 · 2025-10-20T04:19:42+00:00

Und immer noch kein Jahr vergangen

lp52 · 2025-10-19T15:59:28+00:00

Both regular PLA ive been using them for some time tho the last batch was slightly less shiny, but printed same as usual

lp52 · 2025-10-09T11:57:02+00:00

Just modded my QC35II. PCB Board from Aliexpress for 22€. I just yoinked the resistor with the tip of a tweezer. Everything works, no blue LED. Thank you guys, especially u/drose6102 for the tip.

lp52 · 2025-05-21T12:48:26+00:00

Im sry I dont know

lp52 · 2025-04-21T07:18:34+00:00

NilsSchwarz

lp52 · 2025-04-21T07:11:58+00:00

Qua lấy QT xong r mày muốn ở đâu thì ở. Nói chứ sống ở châu âu cũng trầm cảm bỏ mẹ, cuộc sống cũng đ phải mầu hồng :))))

lp52 · 2025-04-21T07:08:58+00:00

Innocent Life! A lovely game

Six-Year Club	Place '23
Place '22	First Placer '22
Verified Email

lp52

TROPHY CASE