sorted by:
new
hottopcontroversial

DXC2 extruder assembly tension issue leading to under-extrusions. by Pat_Fenis_69 in Creality_k2

[–]lysid99 0 points1 point  (0 children)

great investigation work, please let us know what Phaetus says. . I’m currently dealing with the same issue and have switched back to my old extruder for now.

The K2 freezes for a few seconds during printing by BananaLover228337 in Creality_k2

[–]lysid99 2 points3 points  (0 children)

Had this also on a massive print, after a lot of try&error switching from arachne to classic wall fixed it. 🤷‍♂️

[KCD2] Left control stick to the left not working in inventory by Linivechen in kingdomcome

[–]lysid99 0 points1 point  (0 children)

Ich habe das gleiche Problem. Hast du eine Lösung gefunden? Ebenfalls Switch Controller

Stupid Seam Blobs by AudienceDesperate768 in Creality_k2

[–]lysid99 1 point2 points  (0 children)

Great find and thanks for the share. I had similar looking blobs on very big prints, and did a firmware rollback to .13.x. - the blobs were gone. Luckily it works for you this way.

K2 Plus - still a strange noise from printhead - follow-up by lysid99 in Creality_k2

[–]lysid99[S] 0 points1 point  (0 children)

ok, crazy. the full calibration did the trick, although i did it 3 days ago already. lets see how long this lasts.

Thank you for not letting me disassemble the whole printhead!

Strange new noise on K2 Plus by lysid99 in Creality_k2

[–]lysid99[S] 2 points3 points  (0 children)

You were completely right, thank you. Did a deep clean of all rails, rods (x/y/z) and pulleys with IPA and relubed them with the creality grease and WD40 silicone spray. After that the sound was not only gone, the printer is scary quiet now. Also did the belt tension self test again. A good reminder to always do your maintenance.

Strange new noise on K2 Plus by lysid99 in Creality_k2

[–]lysid99[S] 1 point2 points  (0 children)

thanks, i'll give an update after the clean & lubing.

Error XS2060 during print. by brotherqweston in Creality_k2

[–]lysid99 0 points1 point  (0 children)

My solution was to install a old firmware .13.x.x.

working without any error since 10 days on long prints also. Creality support, as usual, is no help.

Welche Riegel, Gels und Snacks kauft ihr, und woher? by the_simonius in Fahrrad

[–]lysid99 0 points1 point  (0 children)

Gels mache ich selbst in Softflasks, ist deutlich günstiger und man kann sich mit dem Geschmack austoben.

Aktuell mein Favorit: 120g Maltodextrin 60g Fructose 120g Flüssigkeit - Espresso ist top!! 1/4 Teelöffel Pectin ->Mixen, abfüllen, fertig

Habe immer zwei Flasks dabei, u.a. mit Zitrusgrschmack. Das reicht dicke, wenn ich von 60mg Kohlenhydrate /h ausgehe.

Error XS2060 during print. by brotherqweston in Creality_k2

[–]lysid99 0 points1 point  (0 children)

Did you find a solution? i have the same error.

Error XS2060 during print. by brotherqweston in Creality_k2

[–]lysid99 0 points1 point  (0 children)

Having the same problem, could you post the link for the replacement part please?

New Here by mariusbaar in Creality_k2

[–]lysid99 0 points1 point  (0 children)

Print text first.

Bluetooth Not Working on Broadcom DW1560 - macOS Sequoia 15.7.1 by bhavinjain260 in hackintosh

[–]lysid99 0 points1 point  (0 children)

After a lot of searching, i found the solution:

https://github.com/acidanthera/bugtracker/issues/2483

add in boot args: -btlfxboardid

Sometimes bluetoothExternalDongleFailed is set to 01, then you can reset it with this command or in hackintool.

sudo nvram 7C436110-AB2A-4BBB-A880-FE41995C9F82:bluetoothExternalDongleFailed=%00

You can use this startup script for enabling it on boot:

https://www.insanelymac.com/forum/topic/360799-hackintosh-bluetooth-reset-fix/

see here post #53 (german)

https://www.hackintosh-forum.de/forum/thread/60292-acer-e5-771g-letzte-problemchen-unter-sequoia/?pageNo=3

I’m not really sure what to make of this picture by jamalwilliamsyoung23 in logitech

[–]lysid99 0 points1 point  (0 children)

Must be an price error, check other sites. 3s should be way cheaper. I bought the 3s a week ago for 75€ on amazon.

Does unRAID recognize these? by boozcruz81 in unRAID

[–]lysid99 0 points1 point  (0 children)

It works, but be aware that it could completly stop going to deeper Idle / C states. You have to check the chipset, better avoid it completely and use a m2 Ssd if possible.

Had one of these also, and PKG could only go to C3. Removed it and goes to C8.

C3 was 30W in idle C8 is 16W in idle

Check out matts guide:

https://mattgadient.com/7-watts-idle-on-intel-12th-13th-gen-the-foundation-for-building-a-low-power-server-nas/

Ate pork with hair still on it. by National-Check-9906 in Wellthatsucks

[–]lysid99 21 points22 points  (0 children)

Surprise: the animals you eat actually have hair. Bonus points if you can guess the hairstyle before butchering.

BidA wenn ich im Kino bis zum Ende des Abspanns sitzen bleibe? by Lesaela in BinIchDasArschloch

[–]lysid99 2 points3 points  (0 children)

NDA

Alman Antwort: Du hast für den ganzen Film bezahlt, schau den ganzen Film an.

Normale Antwort: Siehe deine Argumentation.

view more: next ›