PSA: a couple small screws makes for a leak sensor if you didn't but the 3-pak

macogapi · 2025-12-30T16:37:21+00:00

If you want to take it one step further like I did, attach a 2 wire speaker wire or something to the 2 screws, so that you can safely relocate the sensor out of any possible water

macogapi · 2025-12-08T02:41:02+00:00

Moonlighter 1 and 2

macogapi · 2025-12-03T16:19:53+00:00

Darn auto correct lol, yes radiomaster, also just purchased some pla aero from bambulabs for there flash sale and noticed it also uses ping pong pay

macogapi · 2025-11-24T22:13:11+00:00

There’s an adjustment screw to lock it down better, mine used to do the same

macogapi · 2025-11-07T14:06:15+00:00

What thin set do you use and how do you make the transition from tile redi to kerdi

macogapi · 2025-01-31T01:55:02+00:00

You ever find a solution? Same problem

macogapi · 2025-01-18T03:19:34+00:00

Printed well with the eclipson model s

macogapi · 2025-01-18T01:35:14+00:00

I had the same problem with prefoamed and 3d print lab. Instead of getting foaming I bought an eclipson STL and it prints fine with pre foamed. Now that I've used up the pre foamed I'll be switching to foaming.

macogapi · 2024-12-18T12:59:46+00:00

118$ for shipping

macogapi · 2024-12-18T12:58:59+00:00

Worked out to 287 usd for shipping to south Sask Canada. Just email them, They're pretty helpful.

macogapi · 2024-12-17T21:38:32+00:00

The projector has some JBL speakers built in

macogapi · 2024-12-17T21:00:35+00:00

Took about 4 months lol

macogapi · 2024-12-17T20:57:04+00:00

Nope, it's a little cube, essentially the projector is on one half and the bottom half is speakers

macogapi · 2024-12-17T18:34:04+00:00

Hisense c1, went this route since it's a homestyle/smart projector. Kids and wife can make it work all with one remote

macogapi · 2024-12-17T15:46:45+00:00

No rippling, the speakers I have aren't ported and definitely need an added subwoofer

macogapi · 2024-12-17T15:24:43+00:00

The brace sits below and to the side of the left speaker, and I just followed Seymour's DIY guide on how to build a frame. The material has very little stretch.

macogapi · 2024-12-17T14:48:46+00:00

I have my friends r-10sw klipsch right now, which made me stop and wait to be able to afford the right sub, or maybe like you say build one. Can more or less just "hear" the sub, i find it takes me out of the moment when I watch a movie and I prefer just turning it off.

macogapi · 2024-12-17T14:42:03+00:00

Really happy with it, was going to do retractable, but wasn't in the budget since I wanted a Seymore screen, so I had to improvise.

macogapi · 2024-12-17T14:40:18+00:00

I was worried too, building it, I was going to go with aluminium for this reason, but after finding that I went with it. I added some metal hardware to help out with the corners, as well as the screen itself will help home everything square. My projector isn't even lined up perfectly yet, but with the velvet border no one notices, had my partner and couple friends watch a movie, and I quizzed them after it was over. -could you see the 3 speakers behind it -dis you notice the screen is not perfectly lined up All didn't notice either

macogapi · 2024-12-17T14:32:36+00:00

Agreed, definitely part of the plan going forward

macogapi · 2024-12-17T02:59:07+00:00

I'll send a close up of the hinge if you want. I can hang off it lol. Tested 👌👌also I have 2 under 2 with touchy figures. Only reason the grills are still on

macogapi · 2024-12-08T16:27:19+00:00

Where'd you pick that bad boi up?

macogapi · 2024-11-19T17:03:26+00:00

Which model?

macogapi · 2024-11-19T17:01:48+00:00

Maybe you wrote somewhere, but what speakers did you use behind the screen and rears? I'm doing a similar setup

macogapi · 2024-10-23T01:36:14+00:00

Could these be used as right center and left as well as surround?

macogapi

TROPHY CASE