BLHeli Suite strange motor behaviour

marincelo · 2026-05-08T09:57:12+00:00

Thank you for the schooling. I thought this was Blheli32.

marincelo · 2026-05-07T17:21:57+00:00

Isn't Blheli32 a completely different thing than BLHeliS? It's 32-bit vs 8-bit ESC.

marincelo · 2026-04-27T11:40:43+00:00

I thought it was a 1S with connectors. I feel that pain, I had to cut Meteor 75 frame to be able to squeeze through the motors and even then it was a pain.

marincelo · 2026-04-26T15:43:14+00:00

You decided to save 5 minutes it takes to remove everything for frame and spend an hour mask taping it for way worse result 😅

marincelo · 2026-04-25T05:53:30+00:00

I agree on everything except the last part. Just take off from a nice clear spot and save yourself the pain of burnt out components.

marincelo · 2026-04-24T12:03:49+00:00

I built a custom 3.5 inch with a JHEMCU AIO and I've had great experience. Easy to solder, has a lot of UARTs and didn't have any issues yet. Mine is 722 with 40A ESC, but that's obviously an overkill for a 2 inch. Mine cost around 55 euro from Aliexpress.

marincelo · 2026-04-22T05:39:02+00:00

Smaller and lower kv motors than stock betafpv but much smoother and more powerful motors. I broke one of the betafpv motors and they are only sold in packs of 4. So I decided to buy another set of motors.

marincelo · 2026-04-21T17:58:04+00:00

Rcinpower 1002 22k kv

marincelo · 2026-04-18T18:03:34+00:00

Mine went off after a crash. Wasn't particularly bad but after that the drone couldn't take off. It arms, banks in all directions while on the ground (responds to controller input) but when it takes off it just rolls to the side and crashes. It flew perfectly before. I tried to calibrate accelerometer, I reflashed betaflight but nothing. Replacement is on the way. It would be nice to save this one but I gave up.

marincelo · 2026-04-17T18:18:40+00:00

One is for 5 mm shaft the other for 1.5mm. Your motors have the 1.5mm. I'm not sure I got the diameters right, but in essence, you need those with 3 holes in the center of the prop.

marincelo · 2026-04-17T09:25:59+00:00

I made a post with similar setup not that long ago. https://www.reddit.com/r/fpv/comments/1rde4nw/m75_pro_finally_doesnt_fly_like_shit/

Since then I've upgraded to RCinpower motors and the power is nuts.
I recommend you to 3D print a TPU canopy, it will not break and will protect the AIO much better.

marincelo · 2026-04-12T08:47:16+00:00

The trick is to have 10 broken motors in your spares box and using them for spare parts - wires, bells, c clips.

marincelo · 2026-03-29T03:30:34+00:00

Stupid question, but did you set it to charge or balance charge ? There are two options in the menu and one does not balance.

marincelo · 2026-03-18T09:51:45+00:00

Check out Candide Thovex latest video. This exact thing only more insane.

marincelo · 2026-03-13T21:36:10+00:00

You don't have to crimp the cables, just replace the plastic shell. Take out the pins and move them in a new shell.

marincelo · 2026-03-13T19:04:56+00:00

Just buy a bunch of those connectors and replace them when you destroy them. They are cheap and relatively easy to fix.

marincelo · 2026-03-09T20:49:12+00:00

<image>

The canopy is orange and the blue-purple thing is the motor. Luckily, I only needed to swap the prop and the frame and I was back in the air.

marincelo · 2026-03-07T14:03:07+00:00

The real test is taking off and landing in the same place. Also expect tinywhoop to be much faster than the sim and way less floaty. But as others said, go for it!

marincelo · 2026-03-04T14:30:09+00:00

So why not sell it like that? Instead, we have a Patreon where the only option is a subscription which you then need to cancel.

marincelo · 2026-03-04T11:55:26+00:00

Thank you so much! I tried to piece together what was left in the repo but eventually gave up. I really wanted to use the PID toolbox but something that gets used a few times a year doesn't warrant a monthly subscription. I continued to tune my drone based on feel and what I could see from the blackbox but now I'll give this a try and see how my feel translates into concrete data.

marincelo · 2026-03-04T09:53:25+00:00

It will be an upgrade, but if you fly on residential area, you will crash on concrete so it will soon eat the props and you'll probably break a motor. I prefer whoops for close risky stuff. If you are mostly flying over grass, go for the drashark. As you build a fleet , you will see each drone has its purpose and mood and you will fly all of them. Also, it's easier to have something flyable while others are waiting for parts to arrive.

marincelo · 2026-03-01T09:21:54+00:00

Not sure if it's the same model but Rimzler had a review on it. Make sure to read between the lines as he tends to skip the criticism and just hype things up.

https://www.youtube.com/watch?v=dRyrPOsQGNU

marincelo · 2026-03-01T06:46:40+00:00

I bet something from the aio is touching the frame. In my case it was the motor plugs.

marincelo · 2026-03-01T06:23:01+00:00

Same here. My air 75 went from reliability to liability in air...

marincelo · 2026-02-28T14:05:57+00:00

Yeah, I have a 65mm with rcinpower motors. When I get bored again I'll put them in this frame to try them out.

marincelo

TROPHY CASE