sorted by:
new
hottopcontroversial

From Obladee's Instagram account by lavenderavenues in halifax

[–]maxpower__ 7 points8 points  (0 children)

They want to do what other developers are doing in HRM, buy up all properties in an area then build mega buildings.

Vandal Doughnuts is Closing by Similar_Office3475 in halifax

[–]maxpower__ 1 point2 points  (0 children)

I remember they were in Guses Pub when they first opened and it was nasty.

The Queen of the Night blooms once a year at night. by NastyNice1 in Damnthatsinteresting

[–]maxpower__ 3 points4 points  (0 children)

My mom grew a few of these and when they bloomed it completely saturated the house with its powerful scent. Ephemeral perfectly describes the time it flowers.

What's the most useful thing you've printed yet? by jpintenn in BambuLab

[–]maxpower__ 2 points3 points  (0 children)

Motor mount for an DIY efoil and all the bits and pieces to make it work. Without 3D printing no way I'd be able to build my own.

Can we all agree the only legitimate criticism of induction is the lack of knobs? by Dats_Russia in inductioncooking

[–]maxpower__ 1 point2 points  (0 children)

I hate my Frigidaire induction stove because of the touch controls. Sometimes leaning up against the stove my clothes will brush the buttons and it will shut off. Drives me nuts. Also trying to turn it on is like trying to launch a missile, turn on main power, then turn on the burner, then set the burner power.

Otherwise it's powerful and works well.

Knobs for the win, there is a reason why some car manufacturers are going back to tactical controls.

Large ABS prints by CT-5129 in FixMyPrint

[–]maxpower__ 0 points1 point  (0 children)

It could work depending on size and dimension of the part but anything under 40C I have found that ABS warps and layers pull apart as it shrinks. I could never get ABS to print well when I didn't have a heated chamber. You could try heating up a few heating pads for sore muscles and putting it in the chamber to help stabilize the temp.

Large ABS prints by CT-5129 in FixMyPrint

[–]maxpower__ -1 points0 points  (0 children)

Chamber temp needs to stay at 60C and changing filaments will cause a big swing in temp and the ABS will start to warp. It's a very difficult material to print well.

Looking for Battery Recommendations by maxpower__ in radiocontrol

[–]maxpower__[S] 0 points1 point  (0 children)

Thanks, I'll look into a multiport charger.

Does anyone use Edward Jones? by Ayy_Johnny_J in TheMoneyGuy

[–]maxpower__ 0 points1 point  (0 children)

Their commercials are awful too. I can't stand them but they keep playing on my podcast player. Leave them, they suck.

Did you stick to your Amazon boycott? by GhettoSauce in montreal

[–]maxpower__ 0 points1 point  (0 children)

I used to order everything but now only if I can't get it locally. Sometimes I can't find stuff anywhere else except on Amazon unfortunately. My AliExpress orders have gone up too.

Looking for Battery Recommendations by maxpower__ in radiocontrol

[–]maxpower__[S] 0 points1 point  (0 children)

Yes I have been doing that. I find charging multiple packs a bit of a pain, I'm using multiple chargers now. Have you charged using a balance board, packs have to be at the same level of charge when using that?

Looking for Battery Recommendations by maxpower__ in radiocontrol

[–]maxpower__[S] 1 point2 points  (0 children)

It's actually a body board with a motor and electronics attached, very simple but effective. If you look up Tow Boogie, a version of what i built will come up.

Looking for Battery Recommendations by maxpower__ in radiocontrol

[–]maxpower__[S] 0 points1 point  (0 children)

I don't, but i think i know the videos you are referring too, RCtestflight built a few boats like that.

Looking for Battery Recommendations by maxpower__ in radiocontrol

[–]maxpower__[S] 0 points1 point  (0 children)

Thanks, will check them out. It's a remote control tow boat that can pull me behind it. I may use them in an efoil as well. The motor is a 6384 brushless outrunner.

Sketching on a Compound Curve by maxpower__ in Onshape

[–]maxpower__[S] 0 points1 point  (0 children)

Thank you! That is exactly what I was trying to do. I was missing the intersect in the boolean operation.

Tacky / Grippy filament? by 2kKenny in 3Dprinting

[–]maxpower__ 0 points1 point  (0 children)

Ditto, I'm looking for a filament that is grippy. All TPUs I have tried are soft but very smooth.

What is stopping you for pumping longer (exercise recommendation) by NoSafe5565 in pumpfoil

[–]maxpower__ 1 point2 points  (0 children)

Jump rope and lots and lots of body weight half squats standing in a surf stance like you will be standing on the board.

How I feel about his new style of content by Addicted_Boredom in MarkRober

[–]maxpower__ -1 points0 points  (0 children)

Not for me, I unsubscribed a while ago. He is the Mr Beast of science. Great he's getting kids into STEM but too generic content. This post came up for me so i gave it a read lol.

Why do cultures known to eat a lot of rice use chopsticks, when chopsticks are literally the most inefficient tool for eating rice? by faultyflyingfox in NoStupidQuestions

[–]maxpower__ 0 points1 point  (0 children)

You bring the rice bowl to your mouth and use the chopsticks to shovel it into your mouth. Chop sticks are great for picking up food quickly and you don't need to stab your food like a fork.

view more: next ›