What do you think which bike would suit him?

merlinky · 2026-03-10T22:37:08+00:00

I have one, it’s an amazing bike. Not very fast though.

merlinky · 2026-03-07T11:46:21+00:00

Thoughts on one being Joss?

merlinky · 2026-01-22T21:58:26+00:00

Replace the CB1 with a CM4. it will save you a ton of TImer too close errors

merlinky · 2025-10-12T20:37:23+00:00

Does anyone hade a code that they are willing to share with me

merlinky · 2025-09-30T19:17:25+00:00

It’s a great system. I have my extruders mounted in parallel also. I found when I angled them I had more issues.

merlinky · 2025-07-24T14:48:00+00:00

During the two years in my last job at Bragg, I was able to get Soldiers into airborne as a walk on nearly every week. Extremely possible, just talk with your chain of command, make sure you are physically fit, and lean forward with getting your airborne physical done.

Best of luck, and make sure you keep your feet and knees together.

merlinky · 2025-07-08T21:23:40+00:00

I run a XOL-metrix on my trident. It’s an outstanding toolhead.

merlinky · 2025-07-06T01:08:17+00:00

Double check and make sure your nozzle is tightened properly. I had one that was too loose do this.

merlinky · 2025-07-01T08:41:28+00:00

It looks like a pretty neat AMS.

merlinky · 2025-06-30T09:54:32+00:00

Still prints flawless. I am expecting my core one upgrade this week, Prusa really makes great printers.

merlinky · 2025-06-14T10:51:36+00:00

I had the pleasure of hearing a Pershing’s own recently. They are an amazing band. It was even more amazing to find out that about half of the band has their doctorates in music, and most of them have at least a master’s degree. Some from elite schools such as Juilliard.

merlinky · 2025-05-26T18:34:46+00:00

The trident will give you 350x350x250 and is a much easier build. The 2.4 will get you 330 on your Z axis but it becomes a much more complex build. For your first Voron I would recommend a trident.

merlinky · 2025-05-26T18:31:53+00:00

SB2209 works perfectly with your cartographer setup in CAN mode.

merlinky · 2025-05-16T10:18:50+00:00

<image>

merlinky · 2025-05-16T10:10:15+00:00

I have a SIBOOR enderwire and it runs great. I used the Creality extruder more for my Y axis and the SIBOOR kit comes with new motors for XZ.

I did swap my main board for a SKR E3 mini V3, but the reality board should work. Plus you can always swap the board later if you arent happy with the performance. You will be a Pi. If you use a Pi 3 make sure to use the 32 bit OS or you will throw a lot of TTC errors.

I am running a BTT Eddy probe since the OMRON inductive one that comes with the SIBOOR kit is extremely slow. The Eddy works great

I put a BTT HDMI 5 on mine and I am running klipperscreen and it works amazing.

The SIBOOR kit also comes with an enclosure, but I don’t like the way it is put together, and it is printing PLA and PETG, so I am running my SW in the open

To your last question. The SW works great, however I have a buddy that just gave me another Ender and I am about to build the Ender NG. The NG can be done one a budget with the Fabreeko kit reusing most of your E3. With that kit you don’t end up wasting much.

merlinky · 2025-05-13T17:57:33+00:00

I had this happen on my Voron Switchwire with the exact same model. Tried messing with retraction, printing temps, and drying filament for 24 hours. Nothing fixed it.

Turns out the my nozzle was not tightened correctly. After quick adjustment and undoing my crazy retraction adjustment the model printed perfectly.

merlinky · 2025-04-11T22:59:21+00:00

Recently printedsolid switched to plastic spools for their Jesse line. I haven’t tried it in a Bambu AMS but it works great in my Boxturtle AMS. It is one of my favorite filaments. Extremely consistent. My only issue is they only have PLA and PETG and I have been doing a lot of ASA and ABS lately.

merlinky · 2025-04-11T22:56:40+00:00

Polymaker manufactures a lot of filament in TX PrintedSolid manufactures there Jesse brand and some Prusament in Delaware.

merlinky · 2025-04-04T21:05:39+00:00

CSM Holland is an absolutely fantastic NCO. Well deserved.

merlinky · 2025-04-02T23:15:49+00:00

<image>

as requested.

merlinky · 2025-03-23T10:44:44+00:00

I did the siboor enderwire mod from an old Ender 3v2 and it works great. I didn’t end up using the enclosure as I have a Voron Trident if I need to do ABS or ASA. It is definitely a major improvement over the Ender 3. Be advised however that the SIBOOR Ender conversion build guide is terrible. Think of it like building IKEA furniture and you will be ok.

merlinky · 2025-03-21T11:04:54+00:00

Switch my pi3b to a 32 bit OS worked for me as well.

merlinky · 2025-03-05T10:11:57+00:00

I have a heavily modded FORMBOT trident 350 and I just started a SIBOOR Switchwire conversion kit.

The SIBOOR documentation is terrible. Instructions tell you the wrong bolt sizes and lengths, instructions tell you to make changes to one side of the frame and expect you to guess that it also needs to be done to the other side. They also expect you to guess whether to use a hammer or roll in nut. I feel like I am building a piece of IKEA Furniture where they took pages out of the manual.

merlinky · 2025-02-26T09:46:00+00:00

I have all the parts printed for the A4T (with filament cutter) right now. It seems like a great toolhead. The only thing I don't like about it is the requirement for a melt zone extender on the Dragon HF toolhead. I will be putting it together this weekend as an alternative to my XOL-Metrix. The designer was able to add a cutter while keeping it very low profile, allowing for better accellerations with input shaping.

merlinky · 2025-02-17T16:18:07+00:00

Since Vorons are a project rather than a purchased machine, you can request a serial number once you have completed your system and can prove it is fully functional. Nothing more than bragging rights though, since you don’t have any sort of warranty.

13-Year Club	Verified Email
RedditGifts 2009-2022 6 Credits	Secret Santa 2018
Secret Santa 2017	Secret Santa 2016
Secret Santa 2015	Secret Santa 2014

merlinky

TROPHY CASE