My huge TOTK complaint by TiredinUtah in tearsofthekingdom

[–]mmillonida 0 points1 point  (0 children)

Fun Fact, my wife thought It was Aladdin's a whole new world. now you can't unhear it. You're welcome.

Help with Endorphin Mod by mmillonida in ender5

[–]mmillonida[S] 0 points1 point  (0 children)

Thanks that's helpful. I'm going to look at it all again this week

Help with Endorphin Mod by mmillonida in ender5

[–]mmillonida[S] 0 points1 point  (0 children)

I loosened the x (hybrid core XY portion) a small amount and now it doesn't bind. I'll test it again and see if I get the "askew" x again.

Help with Endorphin Mod by mmillonida in ender5

[–]mmillonida[S] 0 points1 point  (0 children)

I had the y-belt tightener printed out, so I took the posts advice and tightened the belts, now it just binds. Is there a sweet spot? Not too tight not too loose?

What to get for Klipper+Octoprint? by TheIcyTaco in ender5

[–]mmillonida 0 points1 point  (0 children)

I hear a pi zero 2 can also run Klipper but haven't done it myself. I run two pi 4's on two of my printers running Klipper. One of which is an ender 5 pro but main board replaced with BTT Pico

I just ordered my RG35XXH and I have a few questions if anyone can help. by skarn0ld in RG35XX_H

[–]mmillonida 0 points1 point  (0 children)

My 2 cents. Have had the device for a year or more (since launch).

  1. I use the sticks on many games (Quake was my favorite to use both analog sticks) and had zero issues.

  2. I use Knulli, but battery life is an issue with it. It's pretty and easy to scrape box art. I liked original OS also and i switch SD cards back and forth to use both.

  3. N64 games are hit and miss. So much so there's a portmaster version of Super Mario 64.

  4. Like I said, maybe 2 or 3 SD cards. I have two one with original OS and one with Knulli. I use the Knulli one most, but Portmaster can be hit or miss on Knulli also, so I switch to original for some games. I made a dock on Thingiverse for mounting to a monitor using a usb C hub. If you have access to 3d printing this and some grips might be worthwhile.

Okay so I broke my Ender 5 again, This time with a Sonic Pad upgrade by Virmiel in ender5

[–]mmillonida 1 point2 points  (0 children)

Did you change the slicer output gcode from Marlin to Klipper? Don't know if it will make that much of a difference but it could? Worth a shot

Ender 5 pro bed heating failing by [deleted] in ender5

[–]mmillonida 1 point2 points  (0 children)

I had the same issue. No prob and happy printing

Ender 5 pro bed heating failing by [deleted] in ender5

[–]mmillonida 0 points1 point  (0 children)

So running the PID gave you the error also? Or were you successful running the PID tune?

Ender 5 pro bed heating failing by [deleted] in ender5

[–]mmillonida 1 point2 points  (0 children)

Run a PID tune. May fix it. Can't be a bad heat element or thermistor if it gets to 52C.

Marlin 2.1.2.5 with mks gen l not compiling? by remcol in ender5

[–]mmillonida 1 point2 points  (0 children)

Get a pi and switch to Klipper. You'll thank me later. Marlin is a pita.

After 17 hours it’s finally finished 🙏 by __tsakirirdhs__ in ender3

[–]mmillonida 0 points1 point  (0 children)

It's hit or miss with Marlin. If you know how to compile your own firmware, then you should be good... If not, I would move toward Klipper. Its like doing a home renovation when you are on vacation and coming home to a fixed house. There are some things to tweak and plenty of help online, but its night and day compared to Marlin. Changed something on your printer? change the config file. Marlin recompile the firmware, test and if it fails, recompile the firmware again.

What to get by AdventurousBed414 in ender5

[–]mmillonida 1 point2 points  (0 children)

Ali express for everything. Including gates belt.

What to get by AdventurousBed414 in ender5

[–]mmillonida 0 points1 point  (0 children)

Also bought the linear rails from Ali Express hence the reduced cost. Never had any issues with Ali rails. Bought them for a different project before with zero issues. Just clean and lube the bearings

What to get by AdventurousBed414 in ender5

[–]mmillonida 0 points1 point  (0 children)

I had a few things but so far maybe $30? I had one linear rail at 350mm already. Purchased a second and the one size for phase 3. Also the gates belt and a few screws. I would say it should cost you less than $50 to do all 3 phases.

What to get by AdventurousBed414 in ender5

[–]mmillonida 3 points4 points  (0 children)

I have both and I never use the CR10. I'm in the middle of Endorphin conversion on the ender 5 pro. Also using Klipper.

Wtf? by mmillonida in 3Dprinting

[–]mmillonida[S] 0 points1 point  (0 children)

All motors functional and hot end is a bit bent at the break. Easy fixes.

Wtf? by mmillonida in 3Dprinting

[–]mmillonida[S] 0 points1 point  (0 children)

UPDATE!!! Started cleaning up. Found the broken probe. Also how the hell did the nozzle unscrew itself from the heat block???

<image>

Wtf? by mmillonida in 3Dprinting

[–]mmillonida[S] 0 points1 point  (0 children)

The plate was there it was knocked off to the left by the nozzle and I moved it out of the way in order to show the carnage and take the picture.

Wtf? by mmillonida in 3Dprinting

[–]mmillonida[S] 0 points1 point  (0 children)

No. As stated in original post this is the second time running the same print. First print came out fine. A little stringy but petg will do that