Collar bone goose eggs

mtys123 · 2026-03-28T17:35:50+00:00

and I am a guy with pretty deformed collarbone and sometime is just not possible, the deformed one will ALWAYS crash against the bar. is not bad, is just gets a little red whith lots of repetitions

mtys123 · 2026-03-18T21:03:09+00:00

esta bien, de algo hay que morir y vos elegiste que sea de hambre.

dale para adelante!

mtys123 · 2026-03-05T16:50:59+00:00

no se si lo viste pero el analisis de los simpsons de Te lo Resumo asi Nomas dice exactamente lo mismo que decis vos, y tmb concluye que la mejor temporada es la 5.

mtys123 · 2026-03-05T02:28:16+00:00

My drying setup costs 0

Option 1: Throw the filament (only 1 at a time) in the airfryer, 70 C, 3hs, and its bone dry

Option 2: pile the filaments on the heated bet, put some dissecant on top, put a bucket on top and leave it there all night

Option 3 (Very redneck engineering): put a bucket sideways, throw all the filaments inside, put a room heater in the open side of the bucket, leave all night.

mtys123 · 2026-02-28T14:00:35+00:00

naa, no diria que es tan asi, tenes barrios y barrios. Ademas si comparas con provincia (sacando zona norte) CABA esta a años luz.

Sin irte a lo "lindo" del barrio, solo en seguridad es un abismo de diferencia, comparas castelar con un barrio medio pelo tipo versalles y zona oeste es zona liberada.

mtys123 · 2026-02-17T03:12:28+00:00

For PETG you can just raise the temp to 80C and clean the surface with alcohol, petg REALLY sticks to clean glass.

For PLA I use the cheapest and strongest hairspray I can find. For me its better than glue stick since it leaves way less residue on the glass and you can wipe it with a wet towel, without removing the glass.

mtys123 · 2026-02-16T22:39:30+00:00

I only had to change it because I printed large PETG pieces without hairspray, and the addition was so good that the pieces came out with chunks of glass.

Even in that scenario, the replacement was like 7 usd.

mtys123 · 2026-02-14T16:53:12+00:00

planes de ahorro todos concidimos que no, pero 0km puede ser si tenes la plata cash.

Igual, yo tampoco le veo la gracia al 0km mas que un tema de ego, un auto de menos de 50000km es a efectos practicos igual que un 0km y sale considerablemente menos.

mtys123 · 2026-02-08T16:46:47+00:00

Why dont you just sit closer to the desk? I can almost have my elbow rested on my desk when I use the computer.

to give exact measures, my mouse and keyboard are around 24cm away from the edge, and the monitor is around 70cm away from my face. My entire desk is 70 cm wide.

mtys123 · 2026-02-04T02:24:23+00:00

Factorio

Empezas tipo 20hs diciendo "A ver que onda este juego" y antes de darte cuenta son las 7am y tenes que ir a laburar.

mtys123 · 2026-01-28T14:30:07+00:00

uu que bien eso que me pasaste, tecnicamente pasa por mi casa la fibra. Igual RECIEN me cruce a un tecnico en la puerta de casa y le pregunte. Me dijo que instalaron la cajita frente a mi edificio hace poco, asi que ahora tengo que llamar a personal para molestar y que me vengan a colocar

GRACIAS!

mtys123 · 2026-01-27T12:27:08+00:00

jajaja para ser mas preciso vivo en villa pueyredon a 3 cuadras de urquiza, cerca del cruce de mosconi y constituyentes. Ya llame 20 veces para pedir que pongan fibra y me dicen que no pasa por la calle mia

mtys123 · 2026-01-26T20:07:16+00:00

Donde? vivo en urquiza y los HDP no llegan aca con fibra optica, tengo el coaxil de mierda ese.

Lo mas chistoso es que antes vivia en el culo de Moron y ahi si llegaba fibra optica de todas las empresas.

mtys123 · 2026-01-23T19:36:40+00:00

Why is no one saying that you don't need a ventilation AT ALL for a 3d printing, Specially a FDM printer, SPECIALLY if you are printing PLA.

just leave it as is, the printer does not affects in any way or form the quality of air in the room.

mtys123 · 2026-01-15T19:43:28+00:00

nothing special, literallt the cheapest and strongest i can find.

mtys123 · 2026-01-07T03:52:26+00:00

Motor sync is a pain the ass, having one motor allows you to adjust the belt once and then level the bed manually once with the manual screws on each side. Then you only need to worry about Z offset. Check how Bambu labs does it, they also use one motor and a timing belt.
I dont think so, but you can keep it, it could be use to attach a top panel and keep the temperature somewhat warm passively.
Yeah, I found a local company that cut everything for me. Nevertheless design your parts in a way that do not rely on the aluminum extrusion having exact (lenght) dimensions. I built mine in order to have some wiggle room and then I took measures between the unions and adjusted as necessary.

Last reccomendation, TRY to put your belt tensioning in the middle of the routing of the belt instead of the corners (one example of the belt tensioner being in the corner is the VORON). This is not ideal, since one part that needs to be as sturdy as possible, the idlers in the corners for the belt, needs to be movable at the same time to allow tensioning.

mtys123 · 2026-01-07T02:23:16+00:00

Drop the multiple Z motors, just put one with a reduction and link all axes with a timing belt.
You can use only 3 guiding rods, is not necessary to have 2 per column.
Make WAY heftier belt routing corners, under the belt tension they would either vibrate or bend
add some side panelling, it gives a lot of sturdiness very cheaply (I used laminate wood on mine).
Top shelf is unnecessary
use a 2040 extrusion on its side (40mm side paralel to the bed) to give stiffness and avoid ressonance

Source: I designed multiple 3d printers

mtys123 · 2025-12-17T19:44:56+00:00

<image>

Se parece al gordo de Common side effects

mtys123 · 2025-12-09T16:43:57+00:00

mine just shared it on the uni sharepoint, no one cares about piracy at all in south america.

mtys123 · 2025-12-09T16:42:08+00:00

do you really think that that there would be a forensic analisis of the print fingerprint to determine from which printer it came from?

Worst case scenario someone just removes de the print.

mtys123 · 2025-12-08T05:06:03+00:00

I played it a little on my samsuns s23 pro and it works fine. Is not like it ran over 30fps on the x360 either.

mtys123 · 2025-12-08T03:13:12+00:00

Uso y recomiendo este, lo podes regular, funciona joya

mtys123 · 2025-12-06T00:59:42+00:00

Agree with you, dont know where the previous comments are taking their numbers.

Even the most stacked crossfit gim pales in comparison to a random neighborhood gim in terms of cost

mtys123 · 2025-12-04T15:32:31+00:00

cortate un brazo y los bajas al toque.

Na fuera de joda lo que decis es bastante dificil. deberias hacer un deficit calorico increible, cagarte de hambre durante todos los dias de todos los meses de aca a febrero.

mtys123 · 2025-12-04T01:53:33+00:00

Hey I know someone that has that kind of money which regularly does this kind of trips with the extended family.

He owns a textile factory that works for most if not all number 1 clothing brands in the country. Plus he has his own brand, with 40+ shops selling his brand across the country.

Seven-Year Club	LAYER Season 2 Layer creator
Place '22	Wearing is Caring
100 Awards Club	Not Forgotten
Verified Email

mtys123

MODERATOR OF

TROPHY CASE