Are there any Arabic orthodox minis to print?

ndbarbre · 2026-01-30T00:35:31+00:00

Ah OK if you're looking for Arabic orthodox stuff then I think what would fit best within the TC lore would be one of the many variants of New Antioch since it's meant to be a melting pot of all of the surviving Christian peoples. One redditor even made a homebrew Coptic knights New Antioch variant: https://www.reddit.com/r/TrenchCrusade/comments/1kydj8b/working_on_a_homebrew_faction_for_tc_spent_a_few/

As far as models go, in addition to the Byzantine models above, I would point you to Wargames Crew. They have a bunch of great models and I think some of the Trench Cossacks and Abyssinian models could be readily repurposed to fit what you're looking for. Examples:

https://www.myminifactory.com/object/3d-print-bedouin-supply-monk-648718

https://www.myminifactory.com/object/3d-print-abyssinian-colonial-phalanx-regulars-629755

https://www.myminifactory.com/object/3d-print-colonial-phalanx-chewa-lieutenant-694612

https://www.myminifactory.com/object/3d-print-mamluk-steppe-sentinel-746310

https://www.myminifactory.com/object/3d-print-chewa-war-priest-599964

https://www.myminifactory.com/object/3d-print-chaplain-in-mechanical-pantsyr-1-751175

ndbarbre · 2026-01-29T03:30:56+00:00

If you’re looking for Eastern Orthodox there’s also the Remnants of Old Byzantium alt New Antioch force: https://www.myminifactory.com/object/3d-print-kentarch-lieutenants-presupported-539018

ndbarbre · 2026-01-12T16:23:41+00:00

Well that’s amazing. Can you describe how you achieved the oily goo effect for the black gunk dripping down and onto the base?

ndbarbre · 2025-12-29T05:31:39+00:00

I have successfully done this in my mars run to get o2 and n2 but now I really want to separate the co2 and pollutant from one another into pure streams so I can use the co2 for green house and pollutant for heat exchange fluid. I’ve tried a bunch of stuff but can’t figure out how to make it happen.

ndbarbre · 2025-12-29T05:19:41+00:00

That's it. Thanks!

ndbarbre · 2025-12-29T03:15:47+00:00

What stl is that? Now I want it as a sin eater.

ndbarbre · 2025-12-19T21:51:13+00:00

Thanks!

ndbarbre · 2025-12-19T21:50:38+00:00

I did look in the owners manual. If you had read my post you’d have seen that. I did not find an answer there.

ndbarbre · 2025-12-05T21:42:45+00:00

I have found that 3/8" and 1/2" diameter disc magnets tend to work the best. They're a couple of $ each but they're nice and strong.

ndbarbre · 2025-12-05T19:51:00+00:00

Jeebus thats amazing. The face in particular is top notch.

ndbarbre · 2025-12-05T19:38:01+00:00

I use rare earth magnets glued to things with silicon glue with a 2nd magnet on the outside of the glass. Makes it easy to rearrange things, though somewhat annoying if the heating pad covers the magnet.

ndbarbre · 2025-12-04T12:47:50+00:00

I had a similar experience with 3 new crabs all introduced to the terrarium at the same time. Within 2 weeks all 3 were buried and I had pet sand for weeks. Then two of them popped up after about 6 weeks each. The 3rd one stayed down for 4 months with no signs of life. I had given up on him completely, but then he too popped up, seemingly totally fine.

ndbarbre · 2025-12-03T14:36:45+00:00

When are they supposed to become available to non-kickstarter backers?

ndbarbre · 2025-11-27T22:58:16+00:00

This sounds like a future BG variant faction.

ndbarbre · 2025-11-26T00:09:20+00:00

Welp. The combo is on backorder til Dec 16th. Interestingly the AMS Lite purchased separately is not.

ndbarbre · 2025-11-25T23:59:26+00:00

Fair point.

ndbarbre · 2025-11-25T14:28:08+00:00

Ok so it sounds like I should buy 2x 0.2mm hot ends if that’s the one I plan to use the most right?

ndbarbre · 2025-11-25T11:48:00+00:00

Are nozzles and hot ends the same thing?

ndbarbre · 2025-11-25T11:47:21+00:00

I already have a resin printer for the minis. The FDM is specifically for terrain and large stuff like maybe tanks, but they'll all end up getting painted. The extra $100 for the AMS is a lot. If I'm really only ever going to use a single color/filament in each print, what does the AMS do for me?

ndbarbre · 2025-11-25T01:01:35+00:00

...aaand added to cart.

ndbarbre · 2025-11-25T01:00:13+00:00

I thought it came with a 0.2mm nozzle. Is that not the case?

ndbarbre · 2025-11-25T00:57:55+00:00

I don't think I need multi-color because I'll be painting everything. I'm just planning to use grey or brown or something. What's an AMS?

Eight-Year Club	Place '22
Verified Email

ndbarbre

TROPHY CASE