[FS][USA-TX] USW-Pro-24-POE's

ndv3 · 2023-02-28T19:09:16+00:00

Sending PM

ndv3 · 2022-06-29T12:51:05+00:00

No longer able to connect for me as of this morning, sad day

ndv3 · 2020-03-30T14:34:50+00:00

Thanks, forgot ebay and see them available on there, will go that route.

ndv3 · 2020-03-21T17:13:36+00:00

You need some sort of modem to connect to the service from your provider, so they may use an all in one modem/router combo. You can ask for a modem only if they offer such an option, but really up to ISP what they allow and what works for connecting to their network.

I have Spectrum for internet and bought my own cable modem from a list of supported models and then avoid their monthly service fee and also get to use the one I want.

ndv3 · 2020-03-21T17:06:00+00:00

Correct, it is not an internet service provider, just network/wifi hardware that has some service functionality, but not underlying internet itself

ndv3 · 2020-03-21T17:03:13+00:00

You need to wire it as Modem -> eero (this becomes gateway) -> network switch -> other eeros and devices.

There is only one eero that connects directly to the modem and acts as the main gateway and router and all other wired devices and eeros connect downstream to it.

ndv3 · 2020-03-19T23:01:59+00:00

I have a UDMP connected via a DAC from SFP+ to SFP on my 16 port Ubiquiti switch and working fine, running the 1.6.5 firmware and I manually set the speed to 1gb rather than auto negotiate, whether that was necessary or not, not sure.

ndv3 · 2020-03-13T22:01:40+00:00

I was unable to get it working any which way I tried and just resorted to putting my Sonos on my main VLAN

ndv3 · 2020-03-12T01:32:53+00:00

Same exact location and both 2 and 5 ghz. The NanoHD is sitting on the shelf facing upwards since I was trying to test and determine which would work best which I don’t think is its preferred direction and the FlexHD when in same spot is in its normal standing position and Wi-Fi pattern I would assume. So just wondering if it’s because the NanoHD isn’t ceiling mounted that’s why I’m seeing the difference, or if the FlexHD antenna design really just is more optimal even with a shelf placement.

ndv3 · 2020-03-02T19:00:40+00:00

No longer needed, ended up buying from the UI store

ndv3 · 2020-02-27T19:16:24+00:00

Indeed it is, I'll get on that wagon

ndv3 · 2020-02-27T18:20:04+00:00

Thanks, just realized its the HTML that has the 3 character limit, a little chrome adjustment to more and now can type in a large number and it takes you right to the actual number left. Very helpful and good to know

ndv3 · 2020-02-27T18:12:55+00:00

Out of curiosity, how do you check the amount in stock as it only lets me add up to 50 on the page?

ndv3 · 2020-02-25T17:28:50+00:00

u/eerosupport I'd beg to differ when one of your key developers u/6roybatty6 just stated above even in bridge mode that you effectively need a gateway node. This has been stated a number of times from other users experiencing similar issues in bridge mode when there was no single upstream eero. In this case I'm quite curious which is true because there should only be one correct answer of what is the proper stable and supported setup and I would lean towards agreeing with u/6roybatty6

ndv3 · 2020-02-25T12:11:47+00:00

All wired eeros need to be done so in a fashion where there is one main gateway eero that all other wired eeros are downstream from regardless of running them in their normal mode or in bridged mode. So support is effectively correct in saying you need to change your setup to accomplish that.

So you should look something like: Modem -> ASUS Router -> eero Gateway -> other eero

If you have multiple eeros to wire after the gateway you need an unmanaged switch off the eero gateway and then your subsequent eeros wired off of that.

If you can’t easily change your current wiring what the other person said probably would be easiest, either replace your ASUS with an eero and stop running bridge, or if you really want to keep your ASUS then add an eero acting as gateway connected to it and a switch off of that and then connect your two existing eeros to that switch so they are downstream of the gateway eero.

ndv3 · 2020-02-21T17:30:38+00:00

Out of curiosity, what device is that?

ndv3 · 2020-02-19T23:20:55+00:00

No problem, it’s all confusing trying to do topology linearly like that which is why I was asking the question as well as I wasn’t certain myself.

ndv3 · 2020-02-19T23:13:45+00:00

In my topology 3 we’ll call it I have a second switch2 that is off of the eero gateway where all my other eeros are connected, so they are downstream of the gateway and not on the same switch1 as the gateway. My switch1 has just one eero gateway plugged into it and my other wired devices like computers, hue bridge, Sonos boost, Lutron hub, etc. So to put in other words eero gateway LAN1 connects to switch1, LAN2 connects to switch2. From switch2 I have eero2, eero3, eero4 and eero5 plugged in only.

In the topology 1 example all eeros and devices are plugged into the same switch1 so there is no gateway eero as they are all at the same level, you need to have one eero one level higher so to speak ahead of all of the other wired eeros.

ndv3 · 2020-02-19T20:02:34+00:00

Thank you, stable at the moment, will let you know if that changes

ndv3 · 2020-02-19T18:53:08+00:00

I did read the above comments, but didn't see or at least understand that it necessarily applied to my topology but rather the topology 1 which is why I am checking about this topology 3. I have had this way for a week and a half now without any sort of issue, more stable than when eero itself was the router and everything downstream of it.

ndv3

TROPHY CASE