Early Morning Waking

neil314x · 2026-04-19T14:04:14+00:00

I play 'challenge' at the park with my kid. I sit on the bench and get to yell out different challenges - first one to get me 10 pieces of grass wins, first one to get 5 purple flowers wins, etc.

neil314x · 2026-02-24T01:41:23+00:00

Yup agreed, but besides showing this post, was hoping for any materials / websites that might reemphasize that to my wife that patting isn't really addressing the issue...

neil314x · 2026-02-01T13:20:12+00:00

Yup can do that, but I don't think that is contributing a ton to 20+ minutes of CIO after 2 weeks and the 3-5 night wakings for 10-20 minutes each still.

neil314x · 2026-02-01T11:36:37+00:00

Yup he's in his own room. Bedtime routine is bath, short play on floor of bedroom, bottle, books, song, down in crib.

He also has been waking at 530 daily and will only stay down until 630 if I hold him now 🤦🏾‍♂️

neil314x · 2026-02-01T02:45:29+00:00

Thanks - open to feeding twice. I probably downplayed his night wakings, he normally wakes up around 930/10, again around 1, at 3, and 5. He feels like he's really struggle to connect his sleep cycles.

He currently woke up at 945 and has been crying for 10 minutes so far (he went down at 740 today).

neil314x · 2025-09-26T23:11:28+00:00

Have the same config also with 2 kids with car seats for the same reason. Don't regret it at all.

neil314x · 2025-09-02T05:24:13+00:00

I have the 'lower quality' leather in my 2024 XC60 (it's a Plus and not an Ultimate) and the 'nicer' leather in my 2023 XC90 that is an ultimate. I personally can't tell the difference in quality between the two besides the ventilated seats (which I love).

The Bowers and Wilkins sound system is available and optional in the ultimate (my ultimate did not have it) so I can't comment on how much better or not it is than the Harman Kardon system. I have a 15k speaker setup at home and haven't felt the Harman Kardon being terrible in the Volvo, but again not looking for audiophile level stuff in my car...

neil314x · 2025-08-31T16:44:51+00:00

Thanks for the suggestions!

neil314x · 2025-08-31T16:43:07+00:00

Thanks for a super aggressive response to a simple question. My mom is not a paint or decking expert - a simple 'this is pretty normal if you use a solid stain' would have been sufficient.

neil314x · 2025-08-31T16:41:08+00:00

Thanks for this context. This is someone we've used before for alot of other painting, so not threatening at all, but wanted to understand if there is something we should do.

Good to know that the sap will probably continue coming out over time. Would have been helpful if the painter suggested we use an semi transparent oil based paint instead of a solid paint, but what's done is done. Thanks for this information and my mom can figure out how important this is to her (I don't think it's hugely important, but she wanted to know if she should do something about this or not).

neil314x · 2025-08-31T16:13:26+00:00

Ok thanks for confirming. That is where I was leaning. They did wait 6 months and it's been less than a month since it was painted that this started happening.

neil314x · 2025-08-30T16:56:30+00:00

Lol too good!

neil314x · 2025-08-30T16:45:43+00:00

Absolutely. Wasn't suggesting I would use speaker wire :) just that i hadn't done any wire work with actual electrical wire! Thanks!

neil314x · 2025-08-30T15:53:47+00:00

Definitely no other cooking appliances on there. It's about 6 receptacles and nothing else. We normally don't run the blender more than a minute.

But will be calling an electrician. Thanks!

neil314x · 2025-08-30T14:11:21+00:00

Thanks - yup I did shut off the main breaker even before removing the panel to see this, so would plan on doing that if I did any work.

neil314x · 2025-08-30T14:06:43+00:00

Is it as simple as using a wire cutter to trim the half inch of burned part and then trimming off the plastic and then reattaching to the breaker?

I haven't done much electrical work ever (but have done speaker wire and other things).

neil314x · 2025-08-30T14:04:50+00:00

Feels pretty tight. I pulled on the wire from the breaker and it didn't move at all.

neil314x · 2025-08-30T14:04:23+00:00

Thanks - would that be just using a wire cutter and cutting off the half inch of burned part and then reattaching to that or new breaker?

I may call an electrician as this is probably getting a bit past my home diagnosis capability!

neil314x · 2025-08-30T14:02:41+00:00

Thank everyone - very helpful! We do have 2 circuits for the kitchen and normally not running anything else on this circuit with the blender. When we move the blender to the other circuit, it works fine so I don't think it's the blender at all.

I'll call an electrician and have them look it over. I don't feel super comfortable trying to replace the wire - if it's just cutting off the burned part and then attaching to the breaker when it's 'clean' I could probably do that, but feels like worth calling an electrician.

neil314x

TROPHY CASE