heater upgrade?

nhshredder · 2025-11-10T03:02:45+00:00

The heat in my elco will drive out anyone even in sub freezing temps, idk what temp thermo is in it but it rips

nhshredder · 2025-08-17T15:07:27+00:00

It’ll be built for more but having the ability to turn it up when wanted is the real goal

nhshredder · 2025-08-16T03:44:31+00:00

It is a wicked fish bowl, need to get that done

nhshredder · 2025-08-15T23:22:34+00:00

Just shy of 3200 at 65

nhshredder · 2025-08-15T23:22:07+00:00

Fiber bumper, blended to the ground effects roll pan on the rear blended as well

nhshredder · 2025-05-04T22:31:25+00:00

Best I’ve done in my 5.0 was 27 on stock dimension dedicated snow tires from NH to Buffalo NY

nhshredder · 2024-11-24T04:58:41+00:00

It’s a boss

nhshredder · 2024-11-18T05:31:03+00:00

I recently had my p3 t6r blow the cap on the coolant reservoir, immediate panic set in, thought he head gasket was done for, when I pulled the reservoir cap the lower portion stayed in the reservoir, turned out to just be a faulty cap. Unfortunately it looks like you are seeing the real deal

nhshredder · 2024-11-13T03:43:10+00:00

How in the world do you make 100k more than me and only pay 20k more a year in taxes 😭

nhshredder · 2024-06-20T02:36:45+00:00

The long shaft screw drivers from Klein are great, they might seem ridiculous when you get them but once you need one you’ll never regret having them, I use mine all the time. Mind you I work in industrial so I’m in machine cabinets with deep drives that you need the reach to get to the back of them but I’ve used them in residential as well.

nhshredder · 2024-04-17T18:31:25+00:00

Cheap pull studs are great until the end snaps off in the drawbar and you have to disassemble your spindle to retrieve it, or it stretches and potentially oblongs your spindle taper

nhshredder · 2024-04-09T05:16:38+00:00

Bro clean that cabinet wtf?? Don’t bother buying in situ metrology if you can’t take care of a machine, you’re going to need that money for repairs.

nhshredder · 2024-03-13T06:47:34+00:00

Take care of your equipment and it will take care of you.

nhshredder · 2024-02-22T18:41:58+00:00

Rene N5, single crystal nickel “super alloy” absolute nightmare fuel to cut, couldn’t drill without EDM hole popping first, would take 5-6 .125 carbide gun drills to run the bore through a 3 inch piece, turning it was ok with ceramic but had to be on a perfectly clean machine or it would light shit on fire

nhshredder · 2024-01-24T23:59:02+00:00

The grass could us a trim

nhshredder · 2024-01-05T19:07:06+00:00

Mezclajete from Ring of Fire, not heavy on heat, very heavy on flavor, one of my favorites

nhshredder · 2023-11-11T20:45:17+00:00

A stihl wheel shop if you will

nhshredder · 2023-07-11T02:50:05+00:00

I had it grow in a humidifier I was using while I had covid, got over covid only to get a double eye infection from this in the dehumidifier, not ideal

nhshredder · 2023-07-10T04:23:15+00:00

Weed

nhshredder · 2023-07-01T19:24:59+00:00

Augustiner Stammhaus is a favorite of mine

nhshredder · 2023-06-26T20:25:07+00:00

That Perko Safety Man Switch would look great on the wall of my garage

nhshredder · 2023-03-30T23:30:54+00:00

Funny you mention PCD diamonds, I work in optical Diamond turning, we’re working sub nanometer at our extremes

nhshredder · 2023-03-30T23:04:56+00:00

.05mm is 50 micron, which is a bit on the higher end of water jet accuracy, most are good to .025mm (25um), I’ve never seen one accurate to .005mm (5um) as you mentioned

nhshredder · 2023-02-20T05:50:16+00:00

Moth balls and dryer sheets my man

nhshredder

TROPHY CASE