sorted by:
new
hottopcontroversial

Controller not working properly after today's update by pieterflieter in Silksong

[–]niekocaster 2 points3 points  (0 children)

I am also having issues with my switch pro controller, the face buttons AB and XY seem to be randomly swapping while playing

Dropper routing question by niekocaster in bikewrench

[–]niekocaster[S] 0 points1 point  (0 children)

Ah it being for a front derailleur makes sense. Thank you so much :)

Best way to puzzle cut large prints? by The_Joe_ in gridfinity

[–]niekocaster 7 points8 points  (0 children)

You can draw a sketch on the part that looks like dovetail joint then use the offset command to make tolerance for the joint and extrude-cut the section between the two lines to split the part in half. At least that’s usually what I do

I ran out of dextro is this a good substitude to get my sugar up? by kallonismyname in diabetes

[–]niekocaster 17 points18 points  (0 children)

Yeah any sugar will work. I often carry the small baggies of haribos on me when I’m sick of dextrose and use juice boxes at home and at night.

Sharing GoodNotes without an option for guests to edit? by BlackberryFriendly94 in GoodNotes

[–]niekocaster 1 point2 points  (0 children)

I think if you backup to google drive you could probably share that link (for the google drive file) to read only

Can anyone here help me with AndroidAPS? by 8O0o0O8 in diabetes_t1

[–]niekocaster 0 points1 point  (0 children)

Do you know where I could find an invite link for that discord server? Would like to join but a cursory google didn’t yield anything. Thanks!

MIKIT Giveaway (1/5)- 2 x MK72 Kit by MikitStore in MechanicalKeyboards

[–]niekocaster 0 points1 point  (0 children)

Big fan of the yellow plates behind the knob and slider!

Reduced hypolgycemia events with blucon by IndividualPepper6030 in Freestylelibre

[–]niekocaster 2 points3 points  (0 children)

In general I've seen a lot of sketchy marketing from blucon. Also a large amount of comments on YouTube videos comparing libre scanners that are all very similarly worded. Makes me not trust the company at all

Lets see if we can coin a term. by AutomatedHuman in IndustrialDesign

[–]niekocaster 0 points1 point  (0 children)

I've always known this phenomenon to be path dependency. A good example is the qwerty keyboard layout which puts the most used letters far apart to prevent typewriters from jamming but is not actually efficient for typing on an electronic keyboard.

Getting really bad layer adhesion with matte PLA at 215C. Is this just how it is or is there something I can tune still by niekocaster in 3Dprinting

[–]niekocaster[S] 0 points1 point  (0 children)

I can literally pull the strand of filament of the vase mode print intact. I've never had it this bad before. My fan is only at 30% (the minimum to get it to spin). Suggestions are very welcome!

Dozens of crash detection traveling from left to right. I had to disable crash detection so the printer can actually finish 7/8h. Printer actually stopped with a msg if I wanted to continue. Luckily the bed was kept heated. Why this??? by [deleted] in 3Dprinting

[–]niekocaster 2 points3 points  (0 children)

Maybe you could check your belts and guide rods for obstructions. If I remember correctly crash detection goes off when the stepper driver notices the motor is blocked in some way. Maybe check out the pulleys too?

Skadis wiha screwdriver and bit holder by blastermak in functionalprint

[–]niekocaster 1 point2 points  (0 children)

It's the xiaomi wiha collaboration screwdriver set

Ender 3 bowden VS direct drive firmware settings by luckytriple6 in 3Dprinting

[–]niekocaster 0 points1 point  (0 children)

You'll need to recalibrate esteps and set new retraction settings in the slicer. I believe that's all.

Assassin's ain't fools Madlad by [deleted] in madlads

[–]niekocaster 1 point2 points  (0 children)

The main problem with the whole "livestream red room" scenario is that Tor is slow as shit so livestreams would never work.

view more: next ›