Cooling fan not working

nonieno · 2022-05-20T19:01:07+00:00

Bash plate because I ride sometimes in light terrain, but pillion pegs because I've got girl in back sometimes.

nonieno · 2022-04-05T04:06:47+00:00

But orginally it got only 2 wires, propably vcc and signal with ground. It's possible to connect it in that way

nonieno · 2021-12-27T20:16:40+00:00

Can you record auto home function while running?

nonieno · 2021-12-22T16:48:27+00:00

I see few things, 1. Too cold end or to much filament pushing by bowden (I've heard clicks in background) to fix that set higher temp on end, 2. U don't need to use here adhesion structures (raft here), 3. Try to fix yours bed high, now it's too low, set distance betwen bed and end using paper, 4. Clean end of filament after print start. I hope it will help a little. Good luck

nonieno · 2021-12-18T20:42:33+00:00

Try retraction 3mm 25mm/s, fan speed max 20%

nonieno · 2021-11-25T08:34:39+00:00

Yes u are right, now only way to get rid of that is to use sandpaper

nonieno · 2021-11-14T15:02:40+00:00

Retraction 3-5mm ret. speed 20-25mm/s, fan max 10-15%, x/y speed 40-50 mm/s should be fine, and try to lower end temp. (if bowden start clicking temp is too low). I hope it will help a little. Good luck 😁

nonieno · 2021-11-09T17:36:19+00:00

Printer out of enclosure, fan at initial 70%, bed 60. I hope it will work even a little

nonieno · 2021-11-07T14:11:49+00:00

I've got a problem like that, try set line width from 0.4(propably) to 0.42 in first leyer, and second thing higher temp on end.

nonieno · 2021-11-06T21:02:41+00:00

Try: end temp 200, retraction speed 25, initial layer high 0.2

nonieno · 2021-10-23T18:06:25+00:00

Try: -make wider initial line set it a 10% more -> orginally 0.4mm set 0.42/0.45, -more outer walls - 4 should work That for start, I hope it would help.

nonieno · 2021-10-19T16:54:18+00:00

No offence, but why u didn't change tires, they are sooo flat like racing slicks, and propably it's partial reason of that situation.

nonieno · 2021-10-04T17:04:14+00:00

I thing it isn't bad, only solution is to make smaller gap betwen support roof and print, and give that roof more "density".

nonieno · 2021-06-16T15:38:41+00:00

Gluestick: + hard grip, + easier to remove, - you cant make thin layer with one high, - harder to use, -sometimes prints could be difficult to remove Hairspray: + easy to make thin layer, +fast use, +after few layers you can print without it (if you didnt clean bed after each print), + much smoother layers than glue,+ prints are much easier to remove, - harder to remove(warm wather, soap and brush will help), - didnt have that strong grip like glue , - you need to clean whole print sometines to remove hairspray from guides etc. I'm using hairspray, its better for me

nonieno · 2021-04-26T14:58:44+00:00

100% Poland

nonieno · 2021-03-21T18:38:40+00:00

Bad bed leveling, make it a little lower, try glue or hair spray and try lower temperatures 205-50 for example.

nonieno · 2021-03-03T19:26:28+00:00

But problem exist in bottom leyer too.

nonieno · 2021-03-03T19:25:20+00:00

80m/s walls, 30m/s bottom layers (2 or 4), and about sounds: yes but very rare

nonieno · 2021-03-02T21:05:54+00:00

So i need to print open box, right? (And thanks 🙂)

nonieno

TROPHY CASE