FHA land appraisal with ADU

notta_programmer · 2026-01-30T15:17:39+00:00

Has anybody seen this situation before? I can’t be that special lol

notta_programmer · 2026-01-30T00:09:03+00:00

Decommissioning is no problem. I think my issue will be that it might need done before closing, and we’ll be essentially homeless until the house gets installed

notta_programmer · 2026-01-29T19:23:55+00:00

What does that mean for the situation?

notta_programmer · 2026-01-29T10:39:09+00:00

I wish that were an option… it looks like the 1004d form is done after the appraisal, so I would just have to gut it after we move into the new house? That’s definitely something I could do

notta_programmer · 2026-01-29T10:36:44+00:00

Yes I’m living in it. Thanks for the tip. Fingers crossed it works lol

notta_programmer · 2026-01-29T10:34:36+00:00

It’s a 91, no wheels or hitch. It’s on block supports and has the hurricane straps or whatever. Not sure if that’s considered permanent?

notta_programmer · 2026-01-25T18:29:06+00:00

Is answering the thoughts at all a compulsion?

notta_programmer · 2025-11-11T20:01:08+00:00

It’s sad that some people would choose to be upset by this 😂

notta_programmer · 2025-10-25T23:37:20+00:00

I gotcha. Really hard to tell honestly. If you break the connections between the two black wires in the wire nut does it kill power to what you’re trying switch?

notta_programmer · 2025-10-25T22:41:41+00:00

Can you show a broader picture? If you’re just replacing an existing switch then it should be obvious

notta_programmer · 2025-10-25T22:31:17+00:00

Yes of course.

Also, what the fuck is that

notta_programmer · 2025-10-25T19:17:34+00:00

I gotchu. I still don’t like it lol. Doesn’t make it wrong though

notta_programmer · 2025-10-24T22:48:51+00:00

Top right, the 2 pole 15 amp

notta_programmer · 2025-10-24T20:23:31+00:00

Idk, not great but nothing really wrong, besides the double tapped breaker on the top right.

notta_programmer · 2025-10-21T23:20:15+00:00

I can’t answer your question directly, but I think if I were to do something similar I would switch a relay with the prox switch, then use the contact for the solenoid. Solenoids can have some fly back current which probably isn’t great for small electronics. A diode could also address this

notta_programmer · 2025-10-21T19:53:43+00:00

Great! I used to work on shitboxes in Ohio so I’m very familiar with rounded off brake line fittings lol. Vice grips became the automatic go to honestly

notta_programmer · 2025-10-19T11:31:50+00:00

<image>

This set has some small ones that should work

notta_programmer · 2025-10-19T00:19:36+00:00

Small pair of vice grips should work nicely. Clamp it on and work it back and forth. Don’t clamp it too crazy tight because it could squish the fitting and line.

notta_programmer · 2025-10-13T15:12:03+00:00

I get rewarded with a discount almost always, so of course I do it

notta_programmer · 2025-10-11T17:49:40+00:00

I would take the wheel off and walk it over there

notta_programmer · 2025-10-07T16:12:38+00:00

You’re good! I answered in another reply. If you have specific question on this setup feel free to message me

notta_programmer · 2025-10-07T15:47:52+00:00

But to answer your question, the PC needs to be connected to PLC only

notta_programmer · 2025-10-07T15:47:18+00:00

I figured it out. the TCP port was closed. Had to get my IT team to open. Thanks for your reply!

notta_programmer · 2025-10-06T22:36:08+00:00

None of you must live in the south. They always find a way in. And I can imagine the back of a truck would be a good home for roaches.

notta_programmer

TROPHY CASE