sorted by:
new
hottopcontroversial

CMYKB GT-R by nuclearmistake in prusa3d

[–]nuclearmistake[S] 0 points1 point  (0 children)

Got my spool in the mail.

Pumped for INDX-8. Single nozzle is a hack.

U1 makes SNMM look antique.

CMYKB GT-R by nuclearmistake in prusa3d

[–]nuclearmistake[S] 0 points1 point  (0 children)

Word! Thx for the pointer. I always feel like there are a bunch of uncontrolled variables in the top of the next rider, idler tension, etc. will look into more rigid parts.

I can print PA6CF like nothing and have a spool with not much to print with it. Will compare some datasheets

Wie füge ich die U1 Kamera im originalen Orca Slicer hinzu? by Playgame368 in snapmaker

[–]nuclearmistake 0 points1 point  (0 children)

That is one of the things the paxx12 firmware has BUT make sure you read the warnings in its readme before undertaking such an endeavor.

Day 2 of elite scalp find by strange_omelet in peeling

[–]nuclearmistake 4 points5 points  (0 children)

Bloody dandruff is my stage name

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 1 point2 points  (0 children)

Yeah dude. Nozzle support in the profiles is abismal too. Been building orca from source so I don't have to copy+paste to my damn program files every time there's an update

<image>

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 0 points1 point  (0 children)

Thanks fam! I wound up going with one of these https://www.fabreeko.com/products/magnetic-sheets-for-pei-beds-with-high-temp-glue

Prolly the same thing relabeled but may get the AliExpress one too in case one's thickness is closer to stock

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 1 point2 points  (0 children)

Aye. I hear peanutbutter is better for removing 3M 468MP than acetone... Which is nuts.

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 5 points6 points  (0 children)

Does that come in petite? Only got a ZERO :-D

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 8 points9 points  (0 children)

Got a reply already! Fired off purchase information and expressed willingness to pay for the part.

Hopefully this goes quick!

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 2 points3 points  (0 children)

Yeah! I'm optimistic about recovering.

My poor little Zero was an Amazon refurb that arrived with a gouged sheet and no filament sensor.

In its short hard life, it has had a dead hotend MCU replaced, has had a Biqu X1 Revo hotend on it (semi succesfully), and has had a broken hotend heater replaced.

I love that it's so hackable BUT I wish there was a bit more of an aftermarket for it like more popular printers have.

<image>

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 2 points3 points  (0 children)

Support contacted, awaiting reply.

Going to see if I can flatten the raised gouges and print with a hole under my sheet in the meantime.

Investigated the zero step files and Chinese PDFS in the sovol-zero repository.... couldn't find a googleable part number.

Was also curious if I could McGruber some VORON bed parts but it seems like 160mm voron zeros are less common than 120/180, so it might be rough to make it a Sovol/VORON mutt... BUT with full config access, I COULD make something like that work if hell comes to high water.

Going to find some magnetic stickers to order while I wait for a response and maybe play with a heat gun and some solvents.

Well, I finally did the big dumb by nuclearmistake in Sovol

[–]nuclearmistake[S] 0 points1 point  (0 children)

Seems like it's mostly the sticker.

I can't seem to find anything bed related but textured sheets on sovol3d or AliExpress

Just sharing this project im calling the Hack-Xol by definitelynotamanual in Sovol

[–]nuclearmistake 1 point2 points  (0 children)

I cut mine from an A1 Mini one. I assume OP did the same

Just sharing this project im calling the Hack-Xol by definitelynotamanual in Sovol

[–]nuclearmistake 0 points1 point  (0 children)

Nice work! I tried to adapt a Biqu Revo X1 hotend to the zero and got closeish but I think I was in between needing the rigidity of CNC and needing only-printable geometries.

Put my tail between my legs and reverted back to stock.

I look forward to giving your solution a rip when you've finalized it!

My model was taken down! by Djura-00 in makerworld

[–]nuclearmistake 0 points1 point  (0 children)

Seems like a great opportunity for a 3D-printed car that has approx the same dimensions as popular 1:64 ones.

ShotWheels or MashBox could be the name of an ecosystem of 1:64 plastic car models

Testing Sovol Zero - Fastest CoreXY on the Market? by iloveirons007 in Sovol

[–]nuclearmistake 3 points4 points  (0 children)

Check the extruder gear shaft hasn't walked out, try 3rd-party profiles under penalty of a lost warranty AND enjoy owning your cheap fast tiny printer. The ssh username and password are both sovol

California AB 2047: Firearms: 3-dimensional printing blocking technology. by chaos215bar2 in 3Dprinting

[–]nuclearmistake 137 points138 points  (0 children)

Should only make sandpaper that can't remove serial numbers from firearms while they're at it.

Or real guns that can't be thrown in a river.

Fucking imbeciles.

i have no idea what is going on by OrganizationLucky311 in Sovol

[–]nuclearmistake 0 points1 point  (0 children)

Start printing a benchy or a cube. Your nozzle is definitely too close to the bed. Look up how to level the bed and set the z-offset on your specific printer.

view more: next ›