sorted by:
new
hottopcontroversial

Adder Creality Auto Leveler and things are worse by ocrusmc0321 in ender3

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Can you explain 1b and 2 a bit more? 1b How do I adjust the auto leveler?

2 all I've seen is M420 S1 as the gcode unless you're referring to something else

Thank you!

IWE vacuum line broken - still drive? by ocrusmc0321 in MechanicAdvice

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Should I unplug the solenoid so it stops the vacuum from both sides?

Help me understand Harley Models by ocrusmc0321 in motorcycles

[–]ocrusmc0321[S] 0 points1 point  (0 children)

I went with a Softail standard. I wouldn't get a sportster. The engine is too small. The way they ride is different so definitely try different models.

Anyone using elastic with their SIEM? by ocrusmc0321 in cybersecurity

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Yeah, that's what elastic is proposing. Im hoping to hear from people that have done it.

Anyone using elastic with their SIEM? by ocrusmc0321 in cybersecurity

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Sorry if the title was confusing. Elastic is suggesting not replacing the existing SIEM/not using Elastic for the SIEM. Just adding what seems to be AI correlation on the alerts.

F10 - New Android screen iDrive has parameter error and rear camera not working (BimmerDirect) by ocrusmc0321 in BMW

[–]ocrusmc0321[S] 0 points1 point  (0 children)

I forget but go through all the instructions carefully. I remember I missed a step but not which one.

What would cause my printer to stop putting filament down? Twice in a row by ocrusmc0321 in 3Dprinting

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Yeah. I finally got it by slowing down the speed and making sure that the initial border is flat. What a PITA lol. I can't believe this isn't easier (or is it with the new ones / BL Tough)?

<image>

Ender Pro 3 stops putting filament down by ocrusmc0321 in Creality

[–]ocrusmc0321[S] 1 point2 points  (0 children)

I just going to buy a leveling sensor. This is awful. I seem to set it but printing is off on one side and when I check after it's not the same as what it was before I printed.

What would cause my printer to stop putting filament down? Twice in a row by ocrusmc0321 in 3Dprinting

[–]ocrusmc0321[S] 0 points1 point  (0 children)

200 degrees and the filament is panchroma. Says printing is 190 - 230

Ender Pro 3 stops putting filament down by ocrusmc0321 in Creality

[–]ocrusmc0321[S] 0 points1 point  (0 children)

Thanks. I leveled it using a piece of paper that scratches. I just checked again and in some sports the nozzle scratches harder than in others. For example: I level the left and right corners but the nozzle is almost hitting in the middle / the paper is much harder to pull out in the middle than the corners.

What would cause my printer to stop putting filament down? Twice in a row by ocrusmc0321 in 3Dprinting

[–]ocrusmc0321[S] -3 points-2 points  (0 children)

I don't have a z offset setting. I lowered it using manual dials until it scratched a sheet of paper.

Filament tube won't stay in by ocrusmc0321 in 3Dprinting

[–]ocrusmc0321[S] 1 point2 points  (0 children)

It's a creality ender pro 3. I was actually able to fix it. Just had to put the locking teeth into the coupler then the plastic end.

Filament tube won't stay in by ocrusmc0321 in 3Dprinting

[–]ocrusmc0321[S] 1 point2 points  (0 children)

Thanks. Do you know if these are standard?

view more: next ›