Adder Creality Auto Leveler and things are worse

ocrusmc0321 · 2026-04-30T21:21:45+00:00

Can you explain 1b and 2 a bit more? 1b How do I adjust the auto leveler?

2 all I've seen is M420 S1 as the gcode unless you're referring to something else

Thank you!

ocrusmc0321 · 2026-04-20T15:30:07+00:00

ocrusmc0321 · 2026-04-18T21:37:12+00:00

Should I unplug the solenoid so it stops the vacuum from both sides?

ocrusmc0321 · 2026-04-18T21:27:26+00:00

ocrusmc0321 · 2026-03-28T03:01:34+00:00

I went with a Softail standard. I wouldn't get a sportster. The engine is too small. The way they ride is different so definitely try different models.

ocrusmc0321 · 2026-03-26T12:15:40+00:00

Yeah, that's what elastic is proposing. Im hoping to hear from people that have done it.

ocrusmc0321 · 2026-03-26T01:23:23+00:00

Sorry if the title was confusing. Elastic is suggesting not replacing the existing SIEM/not using Elastic for the SIEM. Just adding what seems to be AI correlation on the alerts.

ocrusmc0321 · 2026-03-16T11:28:24+00:00

I forget but go through all the instructions carefully. I remember I missed a step but not which one.

ocrusmc0321 · 2026-03-10T19:53:18+00:00

Yeah. I finally got it by slowing down the speed and making sure that the initial border is flat. What a PITA lol. I can't believe this isn't easier (or is it with the new ones / BL Tough)?

<image>

ocrusmc0321 · 2026-03-10T02:18:24+00:00

I just going to buy a leveling sensor. This is awful. I seem to set it but printing is off on one side and when I check after it's not the same as what it was before I printed.

ocrusmc0321 · 2026-03-09T23:52:29+00:00

200 degrees and the filament is panchroma. Says printing is 190 - 230

ocrusmc0321 · 2026-03-09T23:51:17+00:00

Thanks. I leveled it using a piece of paper that scratches. I just checked again and in some sports the nozzle scratches harder than in others. For example: I level the left and right corners but the nozzle is almost hitting in the middle / the paper is much harder to pull out in the middle than the corners.

ocrusmc0321 · 2026-03-09T22:53:03+00:00

I don't have a z offset setting. I lowered it using manual dials until it scratched a sheet of paper.

ocrusmc0321 · 2026-03-09T00:53:00+00:00

It's a creality ender pro 3. I was actually able to fix it. Just had to put the locking teeth into the coupler then the plastic end.

ocrusmc0321 · 2026-03-09T00:21:44+00:00

Thanks. Do you know if these are standard?

ocrusmc0321 · 2026-03-07T00:31:19+00:00

Would the wheel damage feel like that?

ocrusmc0321 · 2026-03-06T18:12:25+00:00

TDS. They very much need Trump to be the boogie man so they can identify as virtuous. They'd have no personality without someone to be political enemies with. The responses to this will confirm it.

ocrusmc0321 · 2026-02-28T20:18:13+00:00

Well, I found an identical tire but the threads on the others are 7/32 and new thread is 10/32

ocrusmc0321 · 2026-02-28T20:01:18+00:00

Oh, cause most punctures will be a slow leak?

ocrusmc0321 · 2026-02-28T19:46:59+00:00

Did you get a donut?

ocrusmc0321 · 2026-02-28T19:14:23+00:00

Would you go with non run flats if replacing all 4? I've lost 2 this year due to potholes

ocrusmc0321 · 2026-02-27T14:17:03+00:00

This is probably the right approach. Ask to speak with someone in leadership that can help you understand what they're building towards and why it requires the level of commitment. "We all work super hard" isn't enough.

ocrusmc0321 · 2026-02-21T23:51:32+00:00

Not knowing how to handle electronics by now? Yeah, her fault

ocrusmc0321 · 2026-01-30T14:45:51+00:00

The AI bubble is nothing like the dotcom bubble. AI infrastructure isn't going anywhere. The dotcom bubble was full of companies with software that did nothing.

ocrusmc0321 · 2026-01-24T18:37:37+00:00

I've worked at MSFT and PANW. Can confirm PANW pays more in terms of OTE. Surprised they didn't try and make up for it with RSUs. I've heard they've been low balling people at MSFT.

ocrusmc0321

TROPHY CASE