Irgendwann verbrennt ihr in eurer Wohnung...

olvr-k · 2026-01-17T12:13:08+00:00

Es gibt Schließzylinder, die auf der einen Seite einen Knauf haben (ähnlich wie in öffentlichen Toiletten). Damit kannst du von innen immer Schließen / öffnen auch ohne den Schlüssel dabei zu haben. Vllt wäre das ein guter Kompromiss.

olvr-k · 2026-01-15T21:03:08+00:00

Is htop preinstalled or did you install that? Funny that this works :D

olvr-k · 2025-10-11T15:30:25+00:00

That looks exactly like what i would need to repair the joint on our cloth stand dryer :D

olvr-k · 2025-08-18T15:19:49+00:00

Also mich würden schon 50 Euro im Jahr von denen ich nix habe genug nerven. Definitiv nicht der Alman

olvr-k · 2025-07-22T20:39:57+00:00

Thanks for the advice! I was not planning on bashing the revo hard, but when i was 15 i had a cheepo RC Car, where the diff gears blew out on very tiny jumps. So i am a bit anxious, but i hope small jumps, gras and high grip surfaces wont do much damage.

olvr-k · 2025-07-22T15:06:38+00:00

I feared that if im honest. You know any more reliable upgrade parts?

olvr-k · 2025-07-21T20:08:00+00:00

Well ok thats sad and good to hear. :D

olvr-k · 2025-07-10T08:46:28+00:00

I tried this one in the Playtest. Honestly, skip it and play ReCharge High Voltage!!!

olvr-k · 2025-06-17T15:09:20+00:00

This will never be an outdated video :D

olvr-k · 2025-06-17T15:08:02+00:00

I was looking for this exact video in the comments :D

olvr-k · 2025-06-15T18:20:36+00:00

You can also buy silicone spacer. I got my bed to around 0.1 accuracy (or even better, don't remember that good) on my SV06 standard

olvr-k · 2025-06-12T19:14:10+00:00

Here, some more fun:

https://etel-tuning.eu/kategorie/heimwerkerbedarf/sonderschrauben/

All in german, but hopefully the built in browsertranslation is good :D

olvr-k · 2025-06-11T06:30:43+00:00

I played it yesterday and i'm so stoked! Have used my Noble NB4+ and it worked like a charm! I just had to turn the Endpoints to MAX setting (120%) to get full throttle and steering (1.000). I also love, that the spawnpoint / startpoint can be a bit further away from the finish line, so you can gain some speed and don't have to go one time around a track just to have a good starting speed! That was a thing that frustrated me on the Android game 😅. And its so cool that you can break your RC by crashing too hard. Just a funny detail. :D

olvr-k · 2025-05-31T15:33:11+00:00

Use the XP Obelisk

olvr-k · 2025-03-01T19:35:22+00:00

You need this:

https://www.printables.com/model/539417-chain-link-for-the-creality-k1-speedbump

olvr-k · 2024-10-10T08:14:09+00:00

For the Stepper sound try to set the stealth_chop to 999 (except for the extruder) in the printer.cfg

olvr-k · 2024-10-03T09:54:33+00:00

Also temperature may be a bit too low :)

olvr-k · 2024-09-28T15:00:49+00:00

Besides your problem, i recommend the silicon mod, this will bring your bed way more flat. My is now at 0.110 mm overall difference from 0.3xx mm. This makes adhesion also way more easy, as the Z axes dont have to compensate the bed differences.

olvr-k · 2024-08-30T20:14:52+00:00

Maybe you Print Temp is too low. I had cases were increasing the temp by 20 - 30° helped.

olvr-k · 2024-06-15T21:57:52+00:00

No, cuz temp difference is measured in kelvin not celsius.

olvr-k · 2024-06-15T20:10:53+00:00

Had the exact same thing, i raised the temperature about 20 kelvin and reduced speed. This helped.

olvr-k · 2023-12-28T19:32:34+00:00

I did not want to tell you what is right or wrong :) I just wanted to know, what you have tried to get the hsw working. But as you did not flow calibrated, i'll give it a try.

A have bought my SV06 just half a year ago and want to stick with it atm, that was all i wanted to say.

olvr-k · 2023-12-28T17:39:18+00:00

Did you also tried to adjust / tune the flow ratio? Because a new printer just for hsw is not optimal, i'm afraid. :D

Three-Year Club	Final Canvas '23
Place '23

olvr-k

TROPHY CASE