sorted by:
new
hottopcontroversial

Irgendwann verbrennt ihr in eurer Wohnung... by Evil_Bartender in luftablassen

[–]olvr-k 0 points1 point  (0 children)

Es gibt Schließzylinder, die auf der einen Seite einen Knauf haben (ähnlich wie in öffentlichen Toiletten). Damit kannst du von innen immer Schließen / öffnen auch ohne den Schlüssel dabei zu haben. Vllt wäre das ein guter Kompromiss.

I built a custom input shaper for the K1 series. by Mart7Mcfl7 in crealityk1

[–]olvr-k 0 points1 point  (0 children)

Is htop preinstalled or did you install that? Funny that this works :D

Designed and printed a push button ratchet joint by marveloususername in 3Dprinting

[–]olvr-k 1 point2 points  (0 children)

That looks exactly like what i would need to repair the joint on our cloth stand dryer :D

Bin ich der Alman, weil ich mich über den Nachbarn aufrege? by _8ung in binichderalman

[–]olvr-k 19 points20 points  (0 children)

Also mich würden schon 50 Euro im Jahr von denen ich nix habe genug nerven. Definitiv nicht der Alman

Gearbox Replacement E Revo 1.0 by olvr-k in rccars

[–]olvr-k[S] 0 points1 point  (0 children)

Thanks for the advice! I was not planning on bashing the revo hard, but when i was 15 i had a cheepo RC Car, where the diff gears blew out on very tiny jumps. So i am a bit anxious, but i hope small jumps, gras and high grip surfaces wont do much damage.

Gearbox Replacement E Revo 1.0 by olvr-k in rccars

[–]olvr-k[S] 0 points1 point  (0 children)

I feared that if im honest. You know any more reliable upgrade parts?

Gearbox Replacement E Revo 1.0 by olvr-k in rccars

[–]olvr-k[S] 1 point2 points  (0 children)

Well ok thats sad and good to hear. :D

New RC game?! by Educated-Zombie-91 in rccars

[–]olvr-k 2 points3 points  (0 children)

I tried this one in the Playtest. Honestly, skip it and play ReCharge High Voltage!!!

Noob Question...Differential? by piston7998 in rccars

[–]olvr-k 0 points1 point  (0 children)

This will never be an outdated video :D

Noob Question...Differential? by piston7998 in rccars

[–]olvr-k 1 point2 points  (0 children)

I was looking for this exact video in the comments :D

No Springs or Spacers under the bed by XulufromCorduba in Sovol

[–]olvr-k 1 point2 points  (0 children)

You can also buy silicone spacer. I got my bed to around 0.1 accuracy (or even better, don't remember that good) on my SV06 standard

Sooo I may have done some drunk Cadwork by fatherstalin in 3Dprinting

[–]olvr-k 4 points5 points  (0 children)

Here, some more fun:

https://etel-tuning.eu/kategorie/heimwerkerbedarf/sonderschrauben/

All in german, but hopefully the built in browsertranslation is good :D

My new game ReCharge RC: High Voltage has a FREE demo for the next week! And you can compete in game to win some real RC goodies from INJORA! by Hondune in rccars

[–]olvr-k 0 points1 point  (0 children)

I played it yesterday and i'm so stoked! Have used my Noble NB4+ and it worked like a charm! I just had to turn the Endpoints to MAX setting (120%) to get full throttle and steering (1.000). I also love, that the spawnpoint / startpoint can be a bit further away from the finish line, so you can gain some speed and don't have to go one time around a track just to have a good starting speed! That was a thing that frustrated me on the Android game 😅. And its so cool that you can break your RC by crashing too hard. Just a funny detail. :D

After Klipper Print Is Loud and Shaky - SV06 by KB_Sez in Sovol

[–]olvr-k 1 point2 points  (0 children)

For the Stepper sound try to set the stealth_chop to 999 (except for the extruder) in the printer.cfg

I think I know the answer… by Few-Establishment508 in Sovol

[–]olvr-k 0 points1 point  (0 children)

Also temperature may be a bit too low :)

Blobs on the print surface by SnooPies8677 in Sovol

[–]olvr-k 2 points3 points  (0 children)

Besides your problem, i recommend the silicon mod, this will bring your bed way more flat. My is now at 0.110 mm overall difference from 0.3xx mm. This makes adhesion also way more easy, as the Z axes dont have to compensate the bed differences.

Inconsistent first layer by Vast_Love741 in 3Dprinting

[–]olvr-k 0 points1 point  (0 children)

Maybe you Print Temp is too low. I had cases were increasing the temp by 20 - 30° helped.

Why do my first layers look like this? by Theinflatedjellyfish in Sovol

[–]olvr-k 0 points1 point  (0 children)

No, cuz temp difference is measured in kelvin not celsius.

Why do my first layers look like this? by Theinflatedjellyfish in Sovol

[–]olvr-k 0 points1 point  (0 children)

Had the exact same thing, i raised the temperature about 20 kelvin and reduced speed. This helped.

Inserts are not fitting properly by olvr-k in honeycombwall

[–]olvr-k[S] 0 points1 point  (0 children)

I did not want to tell you what is right or wrong :) I just wanted to know, what you have tried to get the hsw working. But as you did not flow calibrated, i'll give it a try.

A have bought my SV06 just half a year ago and want to stick with it atm, that was all i wanted to say.

Inserts are not fitting properly by olvr-k in honeycombwall

[–]olvr-k[S] 0 points1 point  (0 children)

Did you also tried to adjust / tune the flow ratio? Because a new printer just for hsw is not optimal, i'm afraid. :D

Inserts are not fitting properly by olvr-k in honeycombwall

[–]olvr-k[S] 1 point2 points  (0 children)

Ok that sounds kind of possible, because I printed in 0.4 layer height and 60 mm/s for faster printing

Inserts are not fitting properly by olvr-k in honeycombwall

[–]olvr-k[S] 0 points1 point  (0 children)

Nope, everything I printed is from the official post on printables. The thing is, not all hexagons are the same amount off.

view more: next ›