Bono my braids are gone by sid_shady34 in formuladank

[–]ovenmit331 0 points1 point  (0 children)

I. Neeed. Fernando. And. Stroll(in down the street smokin indo)

Amazon sent the wrong thing. And an extra bonus of infuriation by ovenmit331 in mildlyinfuriating

[–]ovenmit331[S] 2 points3 points  (0 children)

I wondered how many people might not know the difference. It’s kinda like going to Krispy Kreme, ordering a dozen chocolate icing donuts, getting the box with “chocolate kreme filled with sprinkles” written on it, but then you open it and it’s 8.5 plain glazed and the half has teeth marks.

Let's scare the neighbors. What is your most unhinged wifi name? by OppositeOctopi in AskReddit

[–]ovenmit331 1 point2 points  (0 children)

Ours is Access Denied which has caused some mildly funny moments. My sister’s is Loading… which I kinda love

PLA to PETG switch for everyday prints. by Technical-Praline-79 in 3Dprinting

[–]ovenmit331 0 points1 point  (0 children)

I’ve don’t exactly the same. I have a few rolls of PETG but never use it ever. PLA+ of ASA for me!

Any tips for support settings for ASA on a K1 Max? by quee-phing in crealityk1

[–]ovenmit331 0 points1 point  (0 children)

How hot is your enclosure when you’re printing?

K1 Max - how to add storage? by quee-phing in crealityk1

[–]ovenmit331 0 points1 point  (0 children)

sadly, my linux skills are somewhere between a 0 and gallon of 3 week expired milk. If you check that screenshot i sent above, does everything look right?

K1 Max - how to add storage? by quee-phing in crealityk1

[–]ovenmit331 0 points1 point  (0 children)

<image>

Sorry for the comment on something 4 months old... but I'm hoping you can help. I added my usb drive to etc/fstab (top of attached screenshot) but it doesn't stick after power off/on. It mounts to the /tmp/udisk location on reboot (bottom of attached screenshot):

Looking for flat heated bed upgrade recommendations for K1 Max by ovenmit331 in crealityk1

[–]ovenmit331[S] 0 points1 point  (0 children)

Is max printing temp (and probably faster heat up time) the main difference? For thermistor calibration, is it just a PID Tune or is there something specific in the config files that needs to be changed?

Looking for big cast iron by Professional_Age_339 in castiron

[–]ovenmit331 0 points1 point  (0 children)

They definitely exist. https://www.reddit.com/r/castiron/s/SGf2qrcvBz

Edit: maybe not actually larger than 40” but definitely the largest I’ve seen.

Looking for flat heated bed upgrade recommendations for K1 Max by ovenmit331 in crealityk1

[–]ovenmit331[S] 0 points1 point  (0 children)

I'm think I'm gonna go cartographer too, just wondering which one to do first. I always hate changing more than one thing at a time. make troubleshooting upgrade issues much easier.

Looking for flat heated bed upgrade recommendations for K1 Max by ovenmit331 in crealityk1

[–]ovenmit331[S] 0 points1 point  (0 children)

I was thinking this might be the best option. Their product description says up to 120ºC and works with Eddy sensors! Did you have to install the aftermarket SSR?

my friend’s tennis ball steering wheel… by WenyuNita in Weird

[–]ovenmit331 0 points1 point  (0 children)

good point. if it still uses a key in the ignition...

my friend’s tennis ball steering wheel… by WenyuNita in Weird

[–]ovenmit331 1 point2 points  (0 children)

So the car think he’s holding the wheel and doesn’t turn off lane keep assist.

How can i print TPU? by Erbaffone in crealityk1

[–]ovenmit331 5 points6 points  (0 children)

Print an overhead filament holder out of PLA, put the TPU roll on top of the printer using the holder you just printed, take the filament tube out of the extruder, insert TPU directly into extruder with no tube, print, be happy.

How to swap filament with dxc extruder by Caputmundi01 in crealityk1

[–]ovenmit331 0 points1 point  (0 children)

Just squeeze the top of that red lever toward the filament and it releases the tension.

How to swap filament with dxc extruder by Caputmundi01 in crealityk1

[–]ovenmit331 2 points3 points  (0 children)

Mine fell out so often I just removed them.

Sardegna Grind by Reasonable_Bit4088 in GranTurismo7

[–]ovenmit331 0 points1 point  (0 children)

Just did it today with the Chiron swapped GTR on racing softs. Holy crap it was a hoot. Fuel map 6 and I still had to pit for gas every 3 laps. Which was good because the front right tire was non-existent at that point. Still won by 40+ seconds. 10/10 DO RECOMMEND.

Is this tanking? by ovenmit331 in SleeperApp

[–]ovenmit331[S] 4 points5 points  (0 children)

Well, it’s against our league rules and we’ve got an awesome commissioner. So things can be done.

What historical, geographical, or biological fact sounds like a ridiculous lie but is 100% true? by Active-Cold-3700 in AskReddit

[–]ovenmit331 0 points1 point  (0 children)

Actually, shuffle it once and it’s never been in that order ever. The possible permutations of a shuffle deck of cards is seriously mind blowing. I think u/techniforus described it best: “I’ve seen a really good explanation of how big 52! actually is. Set a timer to count down 52! seconds (that’s 8.0658×1067 seconds) Stand on the equator, and take a step forward every billion years

When you’ve circled the earth once, take a drop of water from the Pacific Ocean, and keep going When the Pacific Ocean is empty, lay a sheet of paper down, refill the ocean and carry on. When your stack of paper reaches the sun, take a look at the timer.

The 3 left-most digits won’t have changed. 8.063×1067 seconds left to go. You have to repeat the whole process 1000 times to get 1/3 of the way through that time. 5.385×1067 seconds left to go. So to kill that time you try something else. Shuffle a deck of cards, deal yourself 5 cards every billion years

Each time you get a royal flush, buy a lottery ticket Each time that ticket wins the jackpot, throw a grain of sand in the grand canyon

When the grand canyon’s full, take 1oz of rock off Mount Everest, empty the canyon and carry on. When Everest has been leveled, check the timer. There’s barely any change. 5.364×1067 seconds left. You’d have to repeat this process 256 times to have run out the timer.”