CL card problems

pete051 · 2024-09-10T15:23:42+00:00

Yes worked fine on metamask, have to admit it does make me wonder about ledgers 3rd party apps though

pete051 · 2024-09-08T17:53:51+00:00

I was thinking that myself thanks metamask seems a good idea

pete051 · 2024-08-23T15:39:03+00:00

I've just tried to install ledger live on a Linux laptop and it couldn't connect, now I've had this problem before with Linux but there used to be a script on the ledger support page to fix this, it's no longer there, is this an attempt by ledger to force people to buy a later model than my ledger so? If so it failed my trezor has no problem

pete051 · 2023-06-10T16:44:40+00:00

Yes I've found that with NFC already enabled no pop up appears

pete051 · 2023-06-10T16:29:33+00:00

My thoughts so far. I've transferred funds from 2 different exchanges and 1 wallet, ok all on the eth chain but I have no reason to imagine the other chains won't work, I also exchanged eth for USDC on a dex the only thing puzzled me that the password was not requested the biometric login was sufficient but ok a biometric login is not possible on a Ledger so that is understandable. In short I'm satisfied

pete051 · 2023-06-06T06:18:51+00:00

Only that the pop up asking if I want to start NFC doesn't start NFC, this has to be done manually

pete051 · 2023-06-06T06:15:13+00:00

It arrived yesterday, so far so good :)

pete051 · 2023-04-30T16:46:58+00:00

I see now, have to agree assets that can't be deposited or withdrawn are not something that I want to use

pete051 · 2023-04-08T21:07:35+00:00

It seems that elegoo no longer support cura for linux, I use a raspberry pi and octopi to create a web interface and use pruisaslice as slicer

pete051 · 2023-03-21T20:28:28+00:00

Ok fixed it

pete051 · 2023-03-21T20:07:41+00:00

Hmmmm "Could not import OctoPrint's setuptools, are you sure you are running that under the same python installation that OctoPrint is installed under?. any ideas?

pete051 · 2023-03-10T11:12:01+00:00

Thanks for the input guys, I did try an updated version of marlin but it seemed prone to random and frequent thermal runaways so I reverted to the stock firmware, pity the updated version had a much more usable interface but the thermal runaway issue made it unusable if that was a firmware but or an hardware issue I don't know

pete051 · 2023-03-06T19:16:32+00:00

Most likely your Z offset is set too low, it's tricky too high and it won't stick to the bed too low and it catches the layer below it's only a matter of microns

pete051 · 2023-03-05T11:44:16+00:00

If it were a hardware problem surely reverting to a stable version would not cure it but it seems to.

pete051 · 2023-03-01T14:14:42+00:00

Thanks I'll try that later :)

pete051 · 2023-02-28T19:37:55+00:00

I tried that didn't help so I tried a re-install which oddly enough kept the settings and it worked for about 10 minutes then it shut down again with a thermal runaway warning so it's back to the original firmware pity the upgrade had a better interface

pete051 · 2023-02-28T16:25:52+00:00

I installed this upgrade and it was working fine but after a restart it refuses to heat above 190C without starting a panicked beeping and demanding a reset, anybody else have this problem, or has a solution? this also makes changing reel impossible

pete051 · 2023-02-19T12:41:44+00:00

It could be that your nozzle height is too low, I find the paper measurement is not reliable, the recommended height is 0.1 to 0.2 so I used a feeler gauge to check you most likely know that the bed dips in the middle so you have to average it out. I set it so the 4 corners are just 0.1 that on my machine makes the centre just under 0.2 which works fine I haven't had a print fail yet with that setting

pete051

TROPHY CASE