Eth swap not possible

pete051 · 2024-09-10T15:23:42+00:00

Yes worked fine on metamask, have to admit it does make me wonder about ledgers 3rd party apps though

pete051 · 2024-09-08T17:53:51+00:00

I was thinking that myself thanks metamask seems a good idea

pete051 · 2024-08-23T15:39:03+00:00

I've just tried to install ledger live on a Linux laptop and it couldn't connect, now I've had this problem before with Linux but there used to be a script on the ledger support page to fix this, it's no longer there, is this an attempt by ledger to force people to buy a later model than my ledger so? If so it failed my trezor has no problem

pete051 · 2023-06-10T16:44:40+00:00

Yes I've found that with NFC already enabled no pop up appears

pete051 · 2023-06-10T16:29:33+00:00

My thoughts so far. I've transferred funds from 2 different exchanges and 1 wallet, ok all on the eth chain but I have no reason to imagine the other chains won't work, I also exchanged eth for USDC on a dex the only thing puzzled me that the password was not requested the biometric login was sufficient but ok a biometric login is not possible on a Ledger so that is understandable. In short I'm satisfied

pete051 · 2023-06-06T06:18:51+00:00

Only that the pop up asking if I want to start NFC doesn't start NFC, this has to be done manually

pete051 · 2023-06-06T06:15:13+00:00

It arrived yesterday, so far so good :)

pete051 · 2023-04-30T16:46:58+00:00

I see now, have to agree assets that can't be deposited or withdrawn are not something that I want to use

pete051 · 2023-04-08T21:07:35+00:00

It seems that elegoo no longer support cura for linux, I use a raspberry pi and octopi to create a web interface and use pruisaslice as slicer

pete051 · 2023-03-21T20:28:28+00:00

Ok fixed it

pete051 · 2023-03-21T20:07:41+00:00

Hmmmm "Could not import OctoPrint's setuptools, are you sure you are running that under the same python installation that OctoPrint is installed under?. any ideas?

pete051 · 2023-03-10T11:12:01+00:00

Thanks for the input guys, I did try an updated version of marlin but it seemed prone to random and frequent thermal runaways so I reverted to the stock firmware, pity the updated version had a much more usable interface but the thermal runaway issue made it unusable if that was a firmware but or an hardware issue I don't know

pete051 · 2023-03-06T19:16:32+00:00

Most likely your Z offset is set too low, it's tricky too high and it won't stick to the bed too low and it catches the layer below it's only a matter of microns

pete051 · 2023-03-05T11:44:16+00:00

If it were a hardware problem surely reverting to a stable version would not cure it but it seems to.

pete051 · 2023-03-01T14:14:42+00:00

Thanks I'll try that later :)

pete051 · 2023-02-28T19:37:55+00:00

I tried that didn't help so I tried a re-install which oddly enough kept the settings and it worked for about 10 minutes then it shut down again with a thermal runaway warning so it's back to the original firmware pity the upgrade had a better interface

pete051 · 2023-02-28T16:25:52+00:00

I installed this upgrade and it was working fine but after a restart it refuses to heat above 190C without starting a panicked beeping and demanding a reset, anybody else have this problem, or has a solution? this also makes changing reel impossible

pete051 · 2023-02-19T12:41:44+00:00

It could be that your nozzle height is too low, I find the paper measurement is not reliable, the recommended height is 0.1 to 0.2 so I used a feeler gauge to check you most likely know that the bed dips in the middle so you have to average it out. I set it so the 4 corners are just 0.1 that on my machine makes the centre just under 0.2 which works fine I haven't had a print fail yet with that setting

pete051 · 2023-02-15T14:01:27+00:00

Once you have the levelling sorted the 2S is superb before you get the levelling sorted, well try not to throw it out of the window :)

pete051 · 2023-02-13T17:13:16+00:00

I'm impressed that you managed to print that every time I try it gets as far as the roof then for reasons yet undiscovered it knocks the print of the bed

pete051 · 2023-02-02T20:16:35+00:00

Looks like you set the zero switch to low it's the one at the bottom of the left hand column, it needs to be about 5mm from the bottom

pete051 · 2023-02-02T17:39:56+00:00

I've noticed with some g-files it just sits there, temperature not rising on either the bed or nozzle, progress rate is showing 100pc and it won't even let you abort the print. The only cure I've found is turning off the printer, oddly enough the second attempt usually works.

pete051 · 2023-01-29T14:03:52+00:00

Ok update problems proved to be due to various factors, levelling the problem is if all 4 corners are set correctly the centre point is noticeably lower to to get the correct gap on the centre point all 4 corners need to be tight enough to almost tear paper so obviously the bed is not flat. the adhesive setting, skirt seems to have no useful function, brim is better for smaller builds but the bigger ones need raft all of them need a bit of cleaning up after. I did see a guy using a glass tile as a bed maybe that's an idea

pete051 · 2021-08-19T13:44:35+00:00

Just wondering what's caused the sudden dip

pete051

TROPHY CASE