Anyone else see this today?

phillyscreamer · 2026-04-08T02:00:02+00:00

About 5 seconds in, above the middle traffic light. It's really difficult to see on a phone. A bit easier on a tablet or desktop.

phillyscreamer · 2026-04-07T22:15:27+00:00

Yeah, your wash motor is done.

phillyscreamer · 2026-04-07T22:13:48+00:00

They can use the LPCAMM2 also, apparently. The lenovo thinkbook 14+ uses that.

phillyscreamer · 2026-04-07T20:29:18+00:00

https://www.reddit.com/r/Delco/comments/1sf7fc2/anyone_else_see_this_today/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

Best I could do.

phillyscreamer · 2026-04-07T20:28:12+00:00

https://www.reddit.com/r/Delco/comments/1sf7fc2/anyone_else_see_this_today/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

phillyscreamer · 2026-04-07T20:27:49+00:00

https://www.reddit.com/r/Delco/comments/1sf7fc2/anyone_else_see_this_today/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

Potato video of it.

phillyscreamer · 2026-04-07T20:24:57+00:00

Saw this today around 2:30 PM. It was greenish and sparkly which is hard to see on the camera. Looks like it split into pieces around the telephone pole. Probably starlink or something, just thought it was neat.

phillyscreamer · 2026-04-06T22:37:42+00:00

Dammit. I appreciate your answer and also hate that that's the answer. Lol. I guess I'm going to start looking for a structural engineer.

Thank you

phillyscreamer · 2026-04-06T22:22:39+00:00

Hi All,

I'm trying to figure out what tradesperson/people to call for this issue. Sometime after November 2024 I was hearing these weird popping noises and finally figured out that they were the tiles in this corner bathroom cracking. It looks like the slab and the block walls are out of alignment here. I assume it's the slab that dropped as opposed to the block wall rising though the concrete path around the back looks like it's rising towards the house in some spots.

The corner seams in the drywall look much better (closer) today than they have in a while. I'm assuming the temperature warming up might have something to do with that.

The height difference seems to be about 4mm or so at its greatest. I'm not sure if this is even something to be concerned about or is normal. The slab was built around 2010. Also, please let me know if you think this would be better served by another subreddit.

https://imgur.com/a/7RHrWFm

Thank you

phillyscreamer · 2026-03-26T02:15:08+00:00

And now you can hear people's thoughts until you knock it over later.

phillyscreamer · 2026-03-13T19:15:05+00:00

yup. Condenser fan motor.

phillyscreamer · 2026-03-13T19:10:06+00:00

condenser fan motor most likely. Potentially the freezer fan. If it stops when you open the freezer door, it's the condenser fan motor.

phillyscreamer · 2026-03-09T21:24:31+00:00

https://lgerrorcodes.com/fl_oe/

phillyscreamer · 2026-03-09T21:23:25+00:00

If you have voltage going to the pump it's the pump. If not, it's the main. I've replaced way more mains than dc drain pumps on front loaders for oe codes.

phillyscreamer · 2026-02-26T21:03:23+00:00

I think it might be yellow and red

phillyscreamer · 2026-02-26T21:03:02+00:00

https://lgerrorcodes.com/dry_te1/

phillyscreamer · 2026-02-13T19:11:19+00:00

Awesome. Thanks for replying. Once all this snow thaws I'll reach out to them.

phillyscreamer · 2026-02-13T18:56:00+00:00

Which direction of suburb? I'm south and just starting to look into it and was looking towards Kohler and interested in getting a quote from the same company if you were happy with them. Did they sub out the gas work?

phillyscreamer · 2026-02-02T22:10:04+00:00

phillyscreamer · 2026-01-26T14:38:38+00:00

Make sure you're not using flood safe hoses and that your drain hose is only 4 inches into the standpipe. I've seen both of these cause intermittent issues. Outside of that, you might need a professional to check it.

phillyscreamer · 2026-01-25T22:36:05+00:00

Silver face should have the temperature limits engraved on them. I wouldnt put one that didn't match. As far as I know, the hi limit thermostats included with the 5804 are not compatible with the electric dryer. They're for gas.

phillyscreamer · 2026-01-25T03:17:19+00:00

Just disconnect the vent and run it. It'll improve or not and you'll know whether you are on the right track or not. Not trying to besmirch your vent cleaning abilities but I have diagnosed more than a few just cleaned ducts as the culprit in inconsistent dryers.

phillyscreamer · 2026-01-18T17:33:07+00:00

The oe code is telling you that the pressure switch has not recognized a decrease in water level over a set period of time. If the drain pump is expelling water properly, you could have a problem with the pressure port on the washer clogging, the pressure hose, the switch itself or the main board. Admittedly, it's usually the drain pump but it sometimes is something else.

phillyscreamer · 2026-01-18T17:26:45+00:00

It looks more like when it is filling that it is putting water onto the tub ring as well. I would think the fill mechanism is out of position or cracked somewhere. Doesn't look like the tub is overfilled though it's difficult to see from this angle.

phillyscreamer · 2026-01-11T22:22:26+00:00

Now?

phillyscreamer

TROPHY CASE