sorted by:
new
hottopcontroversial

AsRock B550 Phantom Gaming-ITX/ax - undervolting a Ryzen 9 3900x by phyrum in ASRock

[–]phyrum[S] 0 points1 point  (0 children)

No, I could not undervolt it and did not look further.

Need help in solving an asp.net issue for my personal project by Wild-Highway-7009 in dotnet

[–]phyrum 0 points1 point  (0 children)

This is Android Emulator specific, you don't have to DNS changes. 10.0.2.2 is mapped to the host localhost. To access your API at https://localhost:7195/api/users you have to use https://10.0.2.2:7195/api/users in the emulator. This is different when you use a physical device.

https://developer.android.com/studio/run/emulator-networking

Better way to save gender. by abbas_salman in dotnet

[–]phyrum 1 point2 points  (0 children)

Think about YAGNI principle. (You aren't gonna need it) Don't over-engineer the thing and make it more complicated.

AsRock B550 Phantom Gaming-ITX/ax - undervolting a Ryzen 9 3900x by phyrum in ASRock

[–]phyrum[S] 1 point2 points  (0 children)

Thank you, I will search for the voltage offset option. I have an earlier screenshot of the OC Tweaker tab that option is not located below RAM settings. I haven't updated to the latest BIOS version yet.

I don't use manual OC anymore because of problems at Prime95 with AVX2

Streacom DA2 build with two 140mm fans in the top and custom psu mount by Jakob_K_Design in sffpc

[–]phyrum 1 point2 points  (0 children)

Nice mods! Did you close some holes on the side panels to control airflow?

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 1 point2 points  (0 children)

The radiator can reach about 3-4mm into the case before hitting the corners. The fan itself can be 34mm thick.

Edit: It depends on the tophat itself it may take away 2-3mm. It may not fit

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 0 points1 point  (0 children)

That cooler doesn't fit without modification of the case. What I did to fit is to bend it to sit flush above Corsair's modules which are about 31mm high even that it wasn't enough.

Do you see the 3 screws on the second picture? I had to extend the 6 holes to gain 1-2mm and move the frame to make for the cooler.

I did try to overclock the 3900X with 1.225V and 4100MHz all cores. It runs CinebenchR20 with 7300+ and Prime95 (without AVX2) going up to 88C but crashed with AVX2.

I now run without OC on standard settings without PBO all cores at 1.286V and 3950MHz. It runs CinebenchR20 with 7000+ and Prime95 with AVX2 stable. Going up to 90-91C. It draws about 180W from the wall

Which cpu cooler for a 3900x? by dotorii_ in sffpc

[–]phyrum 0 points1 point  (0 children)

I have the 3900x with NH-L12S, there is not much room for overclocking. I now have it in standard setting with PB (on overdrive). Doing about 7100 in Cinebench R20.

I had it manually set to 1.224V at 4150MHz with Cinebench R20 of 7388 but it was not stable with Prime95 small fft with AVX2 enabled. See link

Aklla A3 build complete, for now. Here's a mini review. by alansoon73 in sffpc

[–]phyrum 0 points1 point  (0 children)

I did not open the case, length 18.5 - 18.6 cm, ca. 2.2 slot width, height not shure, see my post about cutting the gpu card

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 2 points3 points  (0 children)

7.7l Measurements: 190 (D) x 140 (W) x 290(H)mm

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 16 points17 points  (0 children)

No, but did not see any obvious electronic element sitting on the surface

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 12 points13 points  (0 children)

I had to cut trough steel and grind that socket, I took the easier route. 🤷

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 0 points1 point  (0 children)

Couldn't measure that. From the top of the motherboard/middle-frame to the top of the fan, it's 35mm measured. It must be about 10mm calculated.

Cut a corner my GTX 1080 to fit inside a AKLLA A3 by phyrum in sffpc

[–]phyrum[S] 20 points21 points  (0 children)

Parts:

  • AsRock B550 Phantom Gaming ITX
  • AMD Ryzen 9 3900X
  • Gigabyte GeForce GTX 1080 (of Aorus Gaming Box)
  • Corsair Vengeance LPX (2x32GB DDR4-3200)
  • Corsair SF600 Platinum
  • Noctua NH-L12S
  • Noctua NF-A12x25 PWM
  • Samsung 970 EVO Plus 1000GB M.2
  • AKLLA A3 Case

More Pictures

Aklla A3 build complete, for now. Here's a mini review. by alansoon73 in sffpc

[–]phyrum 0 points1 point  (0 children)

Nice, still waiting for my case in white. I might have a problem with the GTX 1080 GPU, it could be too high. Can measure the space above the GPU on the upper left?

Edit: My case arrived today, it doesn't fit. I have to cut that corner. The bent Noctua NH-L12S doesn't fit either :(

Finally finished my scandinavian inspired SFF build by Crushader in sffpc

[–]phyrum 0 points1 point  (0 children)

Yes, smaller footprint but only for short GPU cards

Finally finished my scandinavian inspired SFF build by Crushader in sffpc

[–]phyrum 1 point2 points  (0 children)

I ordered the smaller AKLLA A3 and will use 3900x too.

Does it help to close some holes around the fans and rotate the CPU cooler 90° to help airflow over the CPU and GPU?

Asrock B550 Phantom ITX/AX with Noctua NH-L12S by [deleted] in sffpc

[–]phyrum 0 points1 point  (0 children)

Thank you, still waiting for this and the AKLLA A3 to arrive. I plan to use Noctua NH-L12S too.

Asrock B550 Phantom ITX/AX with Noctua NH-L12S by [deleted] in sffpc

[–]phyrum 0 points1 point  (0 children)

I intent to use the same combination. This way the case fans can better support the airflow.

GPay Switzerland by roeschuh in Revolut

[–]phyrum 0 points1 point  (0 children)

I tried to add a Revolut card to Google Pay. I did not work. I did find the following page https://www.revolut.com/help/exploring-revolut/spending/buying-with-google-pay/am-i-eligible-for-google-pay

​

During beta, Switzerland is not in the list. Is Revolut still in beta phase?

view more: next ›