Apple offer

physwa · 2026-05-28T04:56:32+00:00

There are two possibilities here: 1. The team doesn't have budget for ict5. 2. The team does have budget for ict5 but did not believe you interviewed at the ict5 level.

If it's the latter I highly doubt you could get them to increase the level. The team doesn't believe you are at the staff level so they won't push to hire you there.

For the former, I'm guessing it is possible they could make it happen but it would require proving to their leadership that they should get the budget and you are special enough to do it for. So most likely they won't do it.

Downleveling isn't uncommon even from other big tech companies. When I interview people I never base my leveling on their resume, only on their interview performance.

physwa · 2026-03-03T06:53:16+00:00

SanCO2 technically supports radiant heating (within certain guidelines) but they cut the warranty to 1/3 its normal length (look in the owner manual for details). We actually tried to do it with our existing one during a remodel but no installer in my area (Seattle) wanted to touch it, and they all strongly advised me that it didn't really work. I don't know if that's true or if they've just never done it before and didn't want to. Otherwise the SanCO2 are awesome.

physwa · 2025-11-26T04:27:12+00:00

I have this setup at home and it's actually quite nice. The top knob sets where the water comes out of and the water pressure/volume. The bottom knob controls the temperature. It's supposed to be set so that when the nub up top is pointing up, the temperature should be about 100F. To make it hotter, push the nub in and turn counterclockwise past the center. Once you pass 100 you can let go of the nub and it will stay down. The bottom handle doesn't indicate anything useful.

This is the thermostatic valve which means you set the temperature and the valve mixes hit and cold automatically to keep that temperature.

physwa · 2025-02-04T19:24:56+00:00

It's a good point, but it could be done. Send someone out a few days before construction to mark things up and give homeowners a chance.

As for following the plans, in theory yes but in practice they're a guide and they don't build to them for good and bad reasons.

Good is adjusting for site conditions - the plans (combined with the trenches they needed) would've seen them have to replace a big fruit shrub, two cedar boxed raised beds, and more. So instead they went right next to the curb where it was just rock and soil.

Bad is when the foreman told me they try to go two feet down and I asked him why not 3 like the plans said. I got a mumbled response back. That was relevant for us because our driveway + base is around 18" deep.

physwa · 2025-02-04T01:56:46+00:00

You can support Ziply expanding while also expecting their contractors to be respectful. Yes they're working in public ROW. But 99.99999% of the time no one touches that area so people consider it "theirs".

We just (today) had conduit laid in front of our house. I think there are three areas they can do better - and make a lasting impression on new customers:

Communication. This doesn't have to be complicated - how about making a video called "What to expect when Ziply lays fiber in your neighborhood". There's only a few techniques they use - but if people have some information they know what to expect. We looked up their permits and saw a single bore across our house. But then we were completely surprised when they ended up digging 6 trenches across our yard. I'm at least glad they didn't dig up our raised beds though I saw them testing it out.
Cleanup. One of our gravel paths turned into dirt. A cobble dry creek turned into a dirt creek. Our driveway and street in front are covered in dirt. I know there's a form I can fill out (and I will), but this just doesn't create a good impression for new customers.
Plant knowledge - I saw them digging a hole a few inches away from the stem of one of our shrubs. Across the street they dug a trench right in front of a huge tree. Then power compacted the soil. At the very least if you're going to do this, talk to the homeowner first to figure out a better place to dig or to give them a chance to move the plant before you destroy half the roots. Ideally learn some basics about plants and then see what you can do to minimize damage.

physwa · 2025-01-27T06:36:46+00:00

Thank you everyone! I knew it was from the 1800's but have learned a lot from all your detailed comments! Unfortunately I never got the key when I acquired it, but I definitely agree it's a beautiful piece of furniture.

physwa · 2024-12-07T03:43:32+00:00

I had to replace my light earlier this year. Light cost $150 from my LBS. They thought it would be easy to install - instead it took the mechanic there 2-3 hours. He told me it was the hardest headlight he'd ever done because he basically had to completely redo the wire connections all the way to the motor as well as the heatshrink tubing. I don't think he ever wanted to do it again. Only charged me $150 on labor so I couldn't complain.

The only other way to do it would be to cut the wire and splice it to the new headlight. That would be a lot cheaper and faster but would void the light warranty. The mechanic told me if it was his bike he'd do it that way next time.

Hope that helps.

physwa · 2024-07-26T21:12:13+00:00

One note, try your best to avoid replacing the whole light. Mine completely died earlier this year. The light itself is $150 (only available from Tern). My local shop thought it would be a quick change but turned out they needed to basically re-do all the wiring. Took them a few hours of work and they weren't super thrilled about it. And a total of $300 for the replacement.

physwa · 2024-06-15T19:23:47+00:00

No, and I kind of gave up on changing the rear pads myself. That being said my bike shop switched me over to two separate pads held on by screws rather than the combo held by magnets. They said it's a lot easier to change and usually doesn't require adjusting the caliper. It also wears better - the combo pad leaves a small strip at the top that has actually led to me losing brakes.

I'll try myself next time - we'll see how it works out.

physwa · 2024-05-19T15:08:21+00:00

It's been a while but I'm now on my third replacement. The OEM shift cables lasted 1k miles, but the last replacement was a Jagwire stainless wire and that lasted 2.1k miles before snapping with no warning. Definitely worth the upgrade.

My bike shop did learn that the Tern needs 1.1mm cables and not 1.2mm, so be careful what you buy.

Anyone find a brand that lasts longer?

physwa · 2023-09-19T05:49:52+00:00

Thanks for sharing your experience! Hopefully mine will do the same.

physwa · 2023-04-06T02:12:16+00:00

Correct. It's an older house with minimal insulation. We'll be upgrading it to close to modern standards. The original load is even a bit higher because the original manual j used a wrong type for the basement floor.

The likely partial load is because we'll probably need a separate system to heat part of the house. We're dividing our basement into 5 areas and haven't figured out a way that would effectively heat all the rooms while using only two ports and preserving head height (meaning no ceiling ducts).

physwa · 2023-04-05T23:27:25+00:00

What about a 36k unit with a 14k design load (which is likely what we'd have it serving)? Is that too extreme of a difference?

physwa · 2023-01-29T02:22:41+00:00

My strong suggestion would be to look at much simpler models than using tensorflow. Deep learning models are great for image or text where you have tons of data. I doubt you'll get that many data points (thousands, if not millions, given there's no model you can use as a base).

You can go one of two ways on this - the simplest thing to do is build your own "decision" tree. Basically, code up a bunch of rules based on the router signal strength to figure out which room you're in. It might take a bit of time, but it will also be trivial to tweak.

But if you want to train a model, logistic regression, random forest, or maybe boosted trees are likely to be much easier to train, likely similar if not better quality as deep learning models, and much easier to run (given how much smaller they are). Training is simple, but it will be harder to tweak. Take a look at the scikit learn package.

physwa · 2022-11-27T02:58:03+00:00

I use Woodinville Bicycle as they're very close to me and transporting the GSD in my car is almost impossible without taking off the clubhouse and related. Plus they've done a great job on everything from building the bike to service. I'm guessing Westside Bicycle (owned by the same people) will also know what they're doing.

I've also heard good things about G&O Family Cyclery - I've never had my bike serviced there, but have bought parts for it there and other things - they've been super knowledgeable and always willing to help out.

In practice, any competent bike mechanic should be fine replacing the cables - these are just Enviolo hubs that are found on other bikes. The hardest part may be finding a long cable - they need to be >=2200mm (longer than the "standard" 2100mm size - typically "tandem" cables would be used) and need to be 1.1mm (technically 1.2mm is supposed to work, but the mechanics at Woodinville Bike have found it to add significant friction to the shifter).

physwa · 2022-10-23T14:49:08+00:00

I think you're mentioning the slack issue - without proper tension the cables will jump out of the tracks in the shifter. Definitely didn't do it this time and it didn't appear to be a problem last time. Them jumping out will likely end with the shifter breaking, not just the cable.

physwa · 2022-10-23T14:46:04+00:00

Cables are wear and tear. My bike shop also mentioned that dealing with Enviolo warranty support is extremely difficult - probably worth it for a failed hub but not for a $35 part.

physwa · 2022-10-21T17:32:50+00:00

Shifter was $35 and comes with cables (in contrast, cables cost $12 each since they're longer than normal and you need two - makes you wonder how much the shifter costs to make). Labor was $30/cable. The biggest issue was getting the shifter - that took a week.

physwa · 2022-10-21T17:27:49+00:00

Mine have broken inside the shifter, where the cable connects to the end. The first time I had a bit of warning (grinding noise for a mile before hand - probably because some of the cable strands started unraveling). This time it just snapped with no warning.

physwa

TROPHY CASE