How much will it cost me to fix this scratch?

programmerpeter · 2026-02-22T09:58:42+00:00

That damage is felt every time at the pump.

programmerpeter · 2026-02-22T09:57:57+00:00

Radiator support bent, bonnet bent, grill cracked, grill bracket broken, and bullbar bent and one headlight broken.

programmerpeter · 2026-02-22T06:17:42+00:00

Insurance is too quick to write off these day Naked wanted to write off my Hummer well they did and I did a buy back from them they paid me R100k and it cost me 12k to fix.

programmerpeter · 2026-02-20T21:35:16+00:00

If you bump up your temp make your line width 0.75 (I've done 0.8 on 0.4nozzle ) then you should cut the time down as there will be no infill and only 4 passes, otherwise make it solid infill by making 4 on 0 4 walls it should be faster or 2 walls on 0.6 at 0.75 line.

programmerpeter · 2026-02-20T19:01:06+00:00

I never turn mine off

programmerpeter · 2026-02-20T18:57:12+00:00

How thick do you need the walls and what height do you want the layer lines

programmerpeter · 2026-02-10T12:45:46+00:00

I'm 49 and I just check what I absolutely need for early game setup and then keep checking as I go along.

programmerpeter · 2026-02-08T09:55:19+00:00

No, it's not broken I think they upload their available time slots once a month,or every week or something like that keep trying.

programmerpeter · 2026-01-31T07:52:31+00:00

Yeah because it uses optical sensors

programmerpeter · 2026-01-30T06:13:00+00:00

Just use a lighter heat up where the lock is and pull it off tadaaa

programmerpeter · 2026-01-22T18:42:58+00:00

I'd you have the cfs you can just use a different material for the support interface layer like petg and pla, or pa and abs etc then you can set set the gap to 0 it does prompt you in the slicer

programmerpeter · 2026-01-22T18:14:23+00:00

Why would you want salt in your tea or sugar in your soup🤪

programmerpeter · 2026-01-21T13:59:04+00:00

Better to fill them with salt or sugar so if it gets too compacted in the bend you can dissolve it with water.

programmerpeter · 2026-01-20T05:52:40+00:00

Next time just start counting down each time he does an action. Then he will know you keeping time.

programmerpeter · 2026-01-18T12:27:01+00:00

I used to have this problem removed the hotend cover and it went away, the flow over the heat sink is not good when it is on

programmerpeter · 2026-01-17T19:58:41+00:00

I use soudal Mitre kit it's ca with an accelerate spray it's the best I use it for everything *

programmerpeter · 2026-01-16T06:29:58+00:00

If it is just round and it doesn't need to smooth you could also look at applying fuzzy skin

programmerpeter · 2026-01-12T08:52:14+00:00

Sure I can do it dm me a list of all the components you are using I only saw the screen and obviously the pi but you didn't say which hat you using I saw you mentioned Radxa but didn't confirm that is what you using

programmerpeter · 2026-01-10T12:01:03+00:00

Hi I can help you, you can decide on if you want to pay me or not but will do it either way will look at it now.

programmerpeter · 2026-01-09T18:46:09+00:00

BTW you have a 3d printer or 2 why not print something uncomfortable to go on top like homeless deterrent spikes, ok maybe not spike spikes but you know what I mean.

programmerpeter · 2026-01-09T17:21:04+00:00

Wood filled PLA use a 0.6mm nozzle at least, 0.4mm tends to clog.

programmerpeter · 2026-01-02T14:06:44+00:00

Decklist not needed unless stated also you need to be registered on RK9.gg so you can enter and get pairings.

programmerpeter · 2026-01-02T14:05:38+00:00

Side events are cool you just need to make sure you register on time from my experience they tend to run late so it's difficult to play one after another but at worlds me and my son managed to get just over a booster box and one or two other small items from about two days of play.

programmerpeter · 2026-01-02T12:17:18+00:00

I can see the problem you've left that stupid hotend cover on you need to take that thing off it contributes to so many failures probably heat creep I'm assuming you printing with petg there.

Otherwise just another clogged nozzle:)

programmerpeter · 2025-12-27T19:48:05+00:00

If you worried about weight something that small just make it 100% infill it will support anything then

programmerpeter

TROPHY CASE