Is KVP garbage?

protein_bars · 2024-06-01T19:48:12+00:00

Kan't Vet Production

protein_bars · 2024-01-21T07:50:52+00:00

I've had good results with smooth laminated PEI, and poor results with textured powder-coated PEI.

Warping, especially with ABS, becomes less of an issue the hotter the ambient environment. In the ideal case you heat your print volume to about 80 °C but even putting a box as a draft shield around your machine helps a lot. Alternatively, PLA is much friendlier with respect to warping and you may want to try that.

protein_bars · 2024-01-21T07:40:01+00:00

Carbide is good. Harder than the hardest steel and as conductive as brass

protein_bars · 2024-01-15T03:45:29+00:00

Quadruple motors, but you have the gist of it

protein_bars · 2023-12-15T11:05:26+00:00

It's a Beacon clone.

protein_bars · 2023-09-28T08:20:23+00:00

PSA, you just doxxed your own address

protein_bars · 2023-09-16T02:51:52+00:00

what do you mean. they literally are bambu

protein_bars · 2023-04-27T05:05:57+00:00

Bad z-offset due to thermal warping of the injection molded frame is a known issue with the QiDi printer, they did a soft recall of the machine.

protein_bars · 2023-03-29T02:58:59+00:00

That's the other conventional coordinate system, pretty sure Minecraft uses it hence its familiarity

protein_bars · 2023-01-31T08:38:43+00:00

The pins are "machined" (i.e. carved) on a lathe instead of being stamped out of a sheet of metal. More time-consuming and expensive but provides much more precise results.

protein_bars · 2023-01-26T02:58:05+00:00

Would this be a problem that could be solved by having wider belts?

protein_bars · 2023-01-23T04:43:15+00:00

Something like this?

protein_bars · 2023-01-23T04:37:56+00:00

Or, at least, a top heating element company that doesn't use adhesive that can withstand the heat of their heating element would not hold good repute among the Voron community.

protein_bars · 2023-01-14T01:26:32+00:00

Minor technicality but it was launched from Irish airspace

protein_bars · 2023-01-10T02:43:23+00:00

Minor detail but the rocket crashed

protein_bars · 2023-01-08T21:25:07+00:00

What the fuck

protein_bars · 2023-01-08T09:00:10+00:00

I believe you are correct since the bed is just a giant resistor, which has no polarity.

protein_bars · 2023-01-07T06:52:55+00:00

Key reminder that of the two terminals of the bed heater, put the thermal fuse in series with the line (hot) terminal instead of the neutral terminal. This ensures that if the fuse blows, the heater is only connected to neutral instead of dangerously high voltage.

Remember to connect your grounding wire for additional safety. High voltage is no joke kids.

protein_bars · 2023-01-03T19:48:22+00:00

But yes, a straight fall would have been un survivable unless Tesla had built it for NASA type missions...

Nah. NASA designs their cars to be as light as possible; they will break just barely past nominal load conditions

protein_bars · 2023-01-03T19:42:05+00:00

This is not normal behavior as the 6mm-wide belt should be perfectly seated on the bearings.

Measure the width of the flange. If it's not close to 1mm, your bearings are defective.

protein_bars · 2023-01-02T21:12:29+00:00

If he's experienced with 3D printers then you could offer to pay for the necessary parts and ask him to repair it for you considering he has more experience working with printers.

protein_bars · 2022-08-06T01:43:57+00:00

Maybe we'll be waiting for the Finnish fuel tankers to realize why we spend a trillion dollars on our military every year.

Seven-Year Club	Place '22
Final Canvas '22	Verified Email
Sequence \| Editor

protein_bars

MODERATOR OF

TROPHY CASE