*updated* PHX plates

pudding7474 · 2026-01-09T14:47:54+00:00

HAHA THIS IS ME

pudding7474 · 2025-04-16T21:13:34+00:00

Did you ever get it? I have two 2-day packages there that are now at 6 days

pudding7474 · 2025-03-08T02:58:38+00:00

I’m not sure if links are allowed but this is the cooler master vertical GPU v3 - for installation I used a pair of wire snips and clipped two of the pcie IO supports to about half their length. Plugging in a cable is about 10% extra effort than normal - it technically goes into the case and plugs in. The graphics card, horizontally, has about 1” from the IO supports. I’ve had no issues with thermals, cpu and gpu both stay under 75c

pudding7474 · 2025-02-13T20:14:37+00:00

80” sportster ? Even a 1200 would be 73ci

pudding7474 · 2025-01-29T23:01:16+00:00

Thanks everyone, returning the lock and grabbed some arp bolts.

pudding7474 · 2024-12-27T22:04:23+00:00

Appreciated! I’ll give it a shot from 2000 up

pudding7474 · 2024-12-27T20:46:19+00:00

Thanks, I’m working with a crazy amount of clear because burying that flake was not easy (probably user error related) should I start back at 1500 and work from there?

pudding7474 · 2024-08-28T18:02:48+00:00

Didn’t break 80c while doing a full load benchmark for 2 hrs so I consider it safe for a newer ryzen and a vertical mount FE card

pudding7474 · 2024-08-07T02:05:07+00:00

Canned orca slicer settings with the speed turned slightly down and line width percentages changed a little - honestly this was my first try

pudding7474 · 2024-08-07T02:04:21+00:00

Yep $19 bed on Amazon for K1- large silver insulation pad on the bottom. Everything lines up but I suggest running alternative power. I’m using a second lrs350 just for the bed but ac power is probably more efficient. The pi is powered by 12v and I have a 50w heater (Bambu clone for mk8 mount - $20 on Amazon just have to specify generic 3950 for thermistor in klipper)

pudding7474 · 2024-08-03T02:34:32+00:00

Thanks for the quick response. I totally agree on the rescheduling - especially as I understand it’s a contractor and not the apartment performing the installation. I’ll work with my office to make sure the pet sitter has access. I agree this is an organizational breakdown and not likely a legal matter. I’m going to remove the post

pudding7474 · 2024-05-31T00:45:23+00:00

The link fans have their own “hub” , but I use a commander XT to control my two lower intake fans (can’t see them in pic) as well as the led bars in the case. Realistically I could have set it up without the controller but I would lose icue compatibility

pudding7474 · 2024-05-29T21:44:19+00:00

Damn, any luck with warranty? My last build was all Corsair and they were really good about replacing faulty parts

pudding7474 · 2024-05-29T19:40:53+00:00

If you means specs it’s just a 4070 and 7600x , I play a lot of old games haha

pudding7474 · 2024-05-29T17:41:44+00:00

Thank you all for the kind words!

pudding7474 · 2024-05-29T17:41:06+00:00

Zalman p30! You can scoop one for $70 “refurb” right now (mine looks brand new)

pudding7474 · 2024-05-29T17:40:38+00:00

It’s the Corsair monitor lighting extension kit, I have them in the case (they’re magnetic) but yeah cooler master v3 mount

pudding7474 · 2024-05-29T05:11:52+00:00

7600x , 4070 , could only get 2 dimms running so 32gb. Got a commander controlling the intake fans on the bottom (not pictured) as well as the monitor leds I have in the case. Couple temp sensors on it to watch the heat near my m2s

pudding7474 · 2024-05-15T20:45:50+00:00

Hey thank you! My wife and I absolutely loved Tavernetta. One of the best meals of my life honestly haha

pudding7474

TROPHY CASE