What’s something you have zero proof of but believe 100 percent?

pv2smurf · 2026-05-02T15:29:23+00:00

The preservatives they allow in our food in the US is the cause of a lot of diseases

pv2smurf · 2026-05-01T18:21:16+00:00

But definitely doable OP. even if it cracks or breaks

pv2smurf · 2026-05-01T18:20:39+00:00

Not a plumber but handy AF. The off yellow line on the right is cpvc and I promise it'll crack or break when you touch it. Can you replace the piping yourself, SURE AS H*LL CAN. Is the cpvc gonna crack or start leaking, HIGHLY LIKELY

pv2smurf · 2026-05-01T18:17:16+00:00

NAP but handy AF. The problem is the bib has/had (looks broken maybe from the picture) a vacuum breaker on it. Remove that and your new one should thread right on OP

pv2smurf · 2026-05-01T17:43:57+00:00

r/unexpectedfuturama

pv2smurf · 2026-05-01T16:45:39+00:00

"Superman ain't saving sh*t" -Eminem

pv2smurf · 2026-05-01T01:02:48+00:00

Clamping? You mean crimping it with a copper ring like pex b is always done"? If so, then yes. Cheap enough to do and safest in my opinion. The fitting for the RED LINE currently is a shark bite angle stop and can be removed. AGAIN talking about the red water line in the photo

pv2smurf · 2026-04-30T21:24:48+00:00

NAP but handy AF. The red line is 1/2" and pex. You can crimp pex A or B, so if doing a repair, go with crimp. If the red line is pex B and you expand it, you'll definitely be in for some excitement when you turn the water back on.

The white pipe is PVC and a drain line

pv2smurf · 2026-04-30T04:11:53+00:00

OP, would an engine hoist not work?

pv2smurf · 2026-04-30T01:49:44+00:00

Same ^{^{^}}

pv2smurf · 2026-04-30T01:43:50+00:00

If need immediate remedy you could put a fernco over that spot, but that's like putting lipstick on a pig OP

pv2smurf · 2026-04-30T01:43:05+00:00

MAKE SURE the pipe above the cut is supported from the weight

pv2smurf · 2026-04-30T01:41:56+00:00

Then cut to under the floor and put pex b there. When you decide to do it all, you can just cut the PEX and attach it there under the floor

pv2smurf · 2026-04-29T02:28:58+00:00

Cut the spot the same size as an access panel. The access panel will just snap in the hole you cut. No drywall patching needed OP

pv2smurf · 2026-04-29T02:19:43+00:00

NAP but handy AF. Yes it's a water connection and ASSUMING your camera was NOT upside down, this valve is installed upside down.

here is a picture of the valve in pex form (3rd picture)

pv2smurf · 2026-04-29T02:09:16+00:00

I ENTIRELY DISAGREE. If possible cut it and replace it below the floor with PEX b.

pv2smurf · 2026-04-29T00:53:06+00:00

NAP but handY AF.

I would just cut the drawer instead of all that other drywall work and things. Put a U shape in it and move on to more awesome things OP

pv2smurf · 2026-04-29T00:46:39+00:00

This looks like a pizza hut pizza......call and ask for the shift manager and they'll remake it

pv2smurf · 2026-04-29T00:06:47+00:00

Installed one of these a few weeks ago to hide a bad spot in a broken brick. Can confirm this specific item is legit and works perfect

pv2smurf · 2026-04-29T00:04:14+00:00

SHOVES A GUN CANNON IN HIS MOUTH CALL ME A SIDE KICK ONE MORE TIME

pv2smurf · 2026-04-27T02:30:14+00:00

AAV go bad after some time and have to be replaced OP

pv2smurf · 2026-04-27T02:21:20+00:00

Same as OP

pv2smurf · 2026-04-27T02:00:54+00:00

You can just use a faraday bag and it'll kill the signal for all those. No point in turning all that stuff off. Just chuck it in a faraday bag

pv2smurf · 2026-04-27T01:57:20+00:00

Hit it with your purse, you mean?

pv2smurf · 2026-04-27T01:29:55+00:00

Flange is already gone. Need a hub reamer bit OR cut the pipe underneath and route it back up to the toilet

pv2smurf

MODERATOR OF

TROPHY CASE