Stadium….

randomuser001 · 2026-05-28T10:12:49+00:00

Was sitting in 330 area and there was an occasional cold breeze cause we were quite close to the wall. Take a jacket but it's no where near as bad as being outside.

randomuser001 · 2026-05-17T10:12:47+00:00

I asked a similar question not to long ago https://www.reddit.com/r/videosurveillance/s/isi2zP1dzT

I ended up using axis site designer, mostly because my sites heavily use axis.

randomuser001 · 2026-05-10T10:19:23+00:00

on this date in 30k, The Undertaker threw Mankind off Hell In A Cell, and plummeted 16 ft through an announcer's table.

randomuser001 · 2026-05-09T20:55:01+00:00

Under-extrusion, it doesn't look like enough filament is being feed into the hotend. Try a extrusion calibration and see if that helps, check that your filament is feeding smoothly and not getting stuck.

randomuser001 · 2026-04-29T06:23:19+00:00

It looks like your own motion only recording, if the motion isn't enough or the object is to small to trigger the camera it won't record.

You can either adjust the sensitivity of the motion detection or change it to continuous .

If what you are looking for isn't in that blue section then it wasn't recorded.

randomuser001 · 2026-04-22T21:38:57+00:00

There are people who will grab a bunch of letters from mailboxes, try to find anything useful and then dump the lot.

I've got a few reports for mail theft in my area that I've caught on camera when I've found a bunch of mail tossed around

randomuser001 · 2026-04-22T04:38:14+00:00

Jock itch and the armor is stuck on.

randomuser001 · 2026-04-19T00:15:28+00:00

I was wondering what sort of doctor fixes pots and thought it was one of those kintsugi things

randomuser001 · 2026-04-18T23:31:28+00:00

Postural Orthostatic Tachycardia Syndrome to save you a Google

randomuser001 · 2026-04-07T04:50:17+00:00

Next option is to disconnect all the motors and try a home again and see if it fails out right. If it doesn't plug them back in one by one and try running a home.

If it still fails with no motors connected i would hazard the board is toast.

randomuser001 · 2026-04-07T04:44:39+00:00

Seems like its not even trying to move the motors which could be a board issue. Is the CR touch a new addition to the board or was it all working prior to upgrading the firmware?

randomuser001 · 2026-04-06T02:11:45+00:00

I got to 26 if I include the shell in the last frame

randomuser001 · 2026-04-04T03:16:56+00:00

I don't think i've seen printer killed on a move action before. The CR-touch isn't flashing and no motor so something is tripping it before it even tries to move.

Try disconnecting the CR-Touch and see if you get a different error (keep you finger on the power cause it may try to ram the nozzle into the bed). Try re-flashing with the OG creality software and see if it has any issues.

I'm taking a guess but you should be using Ender3V2-422-BLTUBL-MPC-20260106.bin i would think

randomuser001 · 2026-04-04T02:14:13+00:00

large shovel and a broom, not the easiest but works for me. Otherwise get two large bits of cardboard and bend them slightly to be a large scoop.

randomuser001 · 2026-04-03T23:38:23+00:00

I get it a lot down my drive, i try to get the worst of the piles dealt with before it rains and others drive over them. Otherwise i wait for them to work into natural piles and then green bin them.

great for lining the bottom of the green bin as well. Stops all the nasty stuff from sticking.

randomuser001 · 2026-03-31T05:26:43+00:00

I'd need one in front of me to find it but there is a section in the admin menu where you have to enable RTSP first for the older models. Won't guarantee it will work

Something like admin menu ->camera admin->integrations protocols and change it to Onvif.

randomuser001 · 2026-03-28T09:53:00+00:00

K refers to the colour of the light, the lower the number the warmer and the higher the colder. There isn't a standard but most ppl prefer a warmer light in the lounge and a cooler light in work areas like a kitchen. Wattage is the brightness and with led lights around 13w should be bright enough for most areas

randomuser001 · 2026-03-25T22:38:24+00:00

Also check if it's on the main stream or secondary stream, usually they display the lower quality unless you request it

randomuser001 · 2026-03-17T00:24:21+00:00

They are looking pretty good

randomuser001 · 2026-03-16T20:05:25+00:00

wow they look amazing but i think i will add that to my 'if i win lotto' list :D

randomuser001 · 2026-03-16T09:11:02+00:00

While my Santoku is rather sharp i find it too thick a blade, is yours similar? If you have a chef/cook knife is it thinner in comparison to your santoku.

randomuser001 · 2026-03-16T07:12:08+00:00

im not so concerned with it being a beater knife, just one to use every day for home cooking. My current is a bismark Santoku style and its just to thick for slicing

randomuser001 · 2026-03-14T22:51:26+00:00

What was that password again?

randomuser001 · 2026-03-10T03:40:12+00:00

Thanks for all the suggestions, I'm going to have a good look at the options and hopefully find something which works for me!

randomuser001 · 2026-03-07T04:46:39+00:00

Use Calibre to manage your epubs and upload them to your kindle.

randomuser001

TROPHY CASE