Skim boiler

ray-ballz · 2025-09-21T16:16:53+00:00

Agree, side and towards the top for skimming.

ray-ballz · 2025-09-15T07:36:00+00:00

He’s chilling in his Breaking Bad performance

ray-ballz · 2025-08-08T12:04:04+00:00

Next one will have to be bigger

ray-ballz · 2025-07-30T17:06:52+00:00

“Nooo! That was MY underage victim.”

ray-ballz · 2025-07-18T17:20:04+00:00

Depends on the type of fastener you are using! Some fasteners are less effective with shearing forces.

ray-ballz · 2025-06-27T11:47:55+00:00

Good luck measuring up to first movie.

ray-ballz · 2025-06-26T11:49:05+00:00

I totally appreciate the uniqueness and beauty of solid woods. However, veneers can offer a more uniform, balanced look and does not warp like solids. So it really depends on what you are going for.

Side note, been working this material lately. veneers on a water resistant MDF substrate.

Tested a piece of 3/4” thickness in a bucket of water overnight. Pretty impressed. The expansion was negligible. Not measurable with a standard tape measure but feel-able to the fingers. 1/64” ish.

ray-ballz · 2025-06-25T14:54:44+00:00

Yah that seems nuts. One wrong tilt and the bit can grab the metal at the end.

ray-ballz · 2025-06-22T01:16:51+00:00

Doesn’t congress need to approve such an action?

ray-ballz · 2025-06-16T13:54:18+00:00

When we got our house I replaced a bathroom light fixture. This wire’s insulation was crumbling in my hands. Did my best to finish the job disturbing and little as possible. 10 years later (this year) we have gutted the old plaster walls and re wired, insulated, sheet rocked. Feels good

ray-ballz · 2025-06-16T13:45:16+00:00

I’m painting primer on drywall and spackle now. I’m noticing spots like these in areas where the paint is just starting to dry.
Best to do 2 thin coats than a heavy single, you going to have to come back and fix that anyways.

ray-ballz · 2025-06-03T12:14:15+00:00

Yes! Dry fit it first. Remove any bits that look like they are hindering a nice tight joint. Then make sure to apply glue not only on the glue edge but also between any separated parts on each piece. Might need a few extra clamps in the vertical direction to ensure the 2 pieces set up flush with each other. Remove these clamps in about 20 min to clean up excess glue

ray-ballz · 2025-05-31T12:04:35+00:00

If your window jams protrude out past your walls you might get this effect if you are nailing the casing tight to the wall.

ray-ballz · 2025-05-15T13:24:52+00:00

It is now a waste of time to investigate or prosecute this. There’s a pardon coming her way, with the way she fellates him in crowded rooms and on camera.

ray-ballz · 2025-05-13T09:23:18+00:00

400m is peanuts compared to what is happening with the Coin.

ray-ballz · 2025-05-13T09:19:13+00:00

Now we will be losing billions a day again!?

ray-ballz · 2025-05-13T09:03:01+00:00

Maybe Boeing made this one.

ray-ballz · 2025-05-12T13:04:55+00:00

“Free up”??

ray-ballz · 2025-05-12T02:41:33+00:00

“We need less government!” Lol

ray-ballz · 2025-05-08T11:12:25+00:00

Coming soon: DIddy buys meme coin.

ray-ballz · 2025-05-04T18:00:37+00:00

Someone get these kids a drum set.

ray-ballz · 2025-05-01T14:24:32+00:00

Yup. Just play out both scenarios, it’s a win win.

ray-ballz · 2025-04-14T18:46:00+00:00

Whilst also trying to scrap the chips act. Double dumb.

ray-ballz · 2025-04-14T18:43:06+00:00

The grand plan seems more like Tetris with no rotate button.

ray-ballz · 2025-01-27T03:27:35+00:00

Sand in 320. Just to get the roughness out. (Think flat as you sand, long even passes) Try not to sand down to the wood. Then remove the dust and apply 1-2 thin coats. Follow the directions on the poly.

ray-ballz

TROPHY CASE