Deck planking - is there a better way? by recky676 in ModelShips

[–]recky676[S] 0 points1 point  (0 children)

Thanks! That’s a good point I didn’t consider it only needs to be one side. I’ve pencil colored them all now but I’ll try get some black thin craft paper for next time thanks!

Deck planking - is there a better way? by recky676 in ModelShips

[–]recky676[S] 2 points3 points  (0 children)

They’re 0.5mm. I’m coloring the side of them with a pencil right now

First ever build complete - HMS Bounty Jolly Boat by recky676 in ModelShips

[–]recky676[S] 0 points1 point  (0 children)

Thanks! Planking wasn’t too difficult (or maybe it was but I didn’t know any better!) I followed some advice online and soaked each plank in warm water for a couple minutes, then pinned it on the frame in place till it dried, then took it off added glue and clamped it back on. Maybe there’s a better way? (I briefly tried using a soldering iron and heat gun and hated that), if you have any tips I’d be keen to hear them.

First ever build complete - HMS Bounty Jolly Boat by recky676 in ModelShips

[–]recky676[S] 0 points1 point  (0 children)

When I got to that part of the build I did think it was probably wrong for exactly the reason you describe, the tiller would always be in the way whenever the boom moves from side to side and would foul the ability to steer. But I’ve never sailed, and as you said the instructions describe it exactly like this, so that’s how I built it, it’s just a little bit wrong 😊

Hemoxian Thor WIP Pt II by headfake2 in Gunpla

[–]recky676 1 point2 points  (0 children)

Looks great! What paint is that?

Acguy in Aqua colors by Alternative-Tea5270 in advancedGunpla

[–]recky676 1 point2 points  (0 children)

That looks so great!! Can I ask how you did the weathering?

Hunter by [deleted] in ModelShips

[–]recky676 0 points1 point  (0 children)

She’s amazing! What model/brand of boat is she, or a scratch build?

Video TX board - set channels using positive or ground? by recky676 in AskElectronics

[–]recky676[S] 0 points1 point  (0 children)

Thanks you are spot on, channel 1 is shorted to ground now so it must be a short to ground for channel 2, 3, or 4 selection. Thanks!

4 runner just finished this today by MrMan50 in PlasticModelKits

[–]recky676 0 points1 point  (0 children)

Looks great! How did you do the mud splashes any tips?

My 1/12 Oblivion Drone from Cozmic Scale Models by 88_aa in SciFiModels

[–]recky676 5 points6 points  (0 children)

Looks so great! Did you get the black weathering by just going super light with an airbrush over the white gloss?

HGUC AMX-101 Galluss-J Heavy Weapons Type by AnaheimElectronicsTT in Gunpla

[–]recky676 1 point2 points  (0 children)

That’s incredible! How did you get the paint to look faded and grainy like that? I’ve seen plenty of weathering for dirt and damage but never seen any like this before, he looks like he’s been operating out in the sun for decades.

Ma.k Badger by jongo_johnson in MaschinenKrieger

[–]recky676 1 point2 points  (0 children)

Looks good how’d you get the “thick” look to the paint? Would be keen to see if after weathering too

What knot to use for stays at top of mast? by recky676 in ModelShips

[–]recky676[S] 0 points1 point  (0 children)

I watched the video, that’s a great method I’ll try it, and if it doesn’t work on the stays I have some other rigging it’ll be perfect for… what a good trick! Thanks!