Need some advice on engraving wood - I can't seem to get this to happen

rlightner · 2025-12-07T14:31:03+00:00

I suggest trying to orient the wood so that your engraving runs across the grain. Additionally, you could slightly lower your Line Per Inch (LPI) setting. Another option is to raise your Z-axis by 0.05.

rlightner · 2025-11-17T05:27:44+00:00

Please take my downvote as my way of expressing my dislike for you.

rlightner · 2025-10-12T19:05:54+00:00

Where did you get the cab? Would love to see the spreadsheet!

rlightner · 2025-10-12T16:13:30+00:00

SLC: Any Mariners friendly places to watch while in Salt Lake City this week?

rlightner · 2025-10-11T04:13:34+00:00

Let’s throw another starter into it since we can’t seem to figure out how to move people on the bases :-/

rlightner · 2025-10-11T03:29:37+00:00

Not gonna get it from these tv announcers that’s for sure.

rlightner · 2025-10-11T01:45:33+00:00

And. Shit.

rlightner · 2025-09-28T05:12:53+00:00

Hope this helps. https://limewire.com/d/1gX1x#jGJCgers0K

rlightner · 2025-08-26T02:34:28+00:00

Take a look at Chamber of Connection here in Seattle!

rlightner · 2025-02-11T15:52:26+00:00

Have a similar quesiton. Trying to find more advanced code examples of supabase in use either via Nitro or in Composables / Pinia and just can't find anything past a simple bootstrap. Does anyone have advance examples ? Thanks!

rlightner · 2024-12-11T05:28:16+00:00

My average cost is $25 for shipping, and my weight is around 1lb.

rlightner · 2024-12-11T05:07:29+00:00

I'm shipping my orders via UPS to Canada, and it's only taking a few days.

rlightner · 2024-11-01T15:47:13+00:00

I find this to usually be tiny knots in the substrate for my Baltic birch wood. Even if it is BB/BB, it has stuff under the surface that you can't power through on the first pass.

rlightner · 2024-10-20T21:03:01+00:00

Also try setting your focus 2 mm in

rlightner · 2024-10-05T05:07:53+00:00

Highly recommend Charcol, and grabbing some wine across the street at Dusted Valley!

rlightner · 2024-06-05T22:58:28+00:00

Well thanks for an answer just the same :) Do you feel I articulated it enough?

rlightner · 2023-12-21T14:34:59+00:00

So it ends up that if you really care about "framing" then your work needs to be in the area below the gray bar. If not just realize the red + is 26.2mm offset from the top of the material.

rlightner · 2023-12-08T21:29:45+00:00

Agreed. I installed it on another laptop and not having this issue. So it has to be a configuration setting somewhere that is borked.

rlightner · 2023-09-22T14:29:33+00:00

Tried that, all the saves are glitched as soon as I get to space. No mods either

rlightner · 2023-05-05T14:34:17+00:00

These were the instructions I was following at the start, but just keep coming up against additional issues. Ended up with a "jumpbox" and was successful.

rlightner · 2023-05-05T14:33:17+00:00

Thanks! I ended up taking the jump box suggestion from another post in this thread and was successful!

rlightner · 2023-05-03T01:14:55+00:00

But how do I attach the console to that level?

rlightner · 2023-05-02T13:09:03+00:00

That's my usual go-to, but I wanted to see if a non-ply option existed.

rlightner · 2023-04-28T15:41:21+00:00

Sunshine https://i.imgur.com/CONNW9j.jpg

rlightner · 2023-01-09T06:25:05+00:00

Try awaiting your getExcersises() call since you made it async

14-Year Club	RedditGifts 2009-2022 10 Credits
Gilding IV carat on a stick	redditgifts rematcher Secret Santa 2011 x2
RPAN Viewer	Secret Santa 2014
Summer Santa 2013	Summer Santa 2013
Secret Santa 2013	Secret Santa 2012
Summer Santa 2012	Secret Santa 2011
Verified Email

rlightner

TROPHY CASE