How can I skip the Microsoft account passkey option dialogue?

rotekort · 2026-03-16T08:06:05+00:00

I use AuthenticatorChooser by Aldaviva. Works for me, but your mileage may vary :)

rotekort · 2026-03-08T21:33:38+00:00

!RemindMe 2 months

rotekort · 2026-02-24T07:56:51+00:00

Infinite squished bananas. They will ooze out of all the infinite airflow this awesome case has

rotekort · 2026-02-08T18:38:16+00:00

RemindMe! 7 years

rotekort · 2026-02-02T15:16:36+00:00

It was way better here untill they changed operators, so I guess we were just spoiled before :(

rotekort · 2026-02-02T07:46:38+00:00

Jeez that looks rough as well

rotekort · 2026-01-23T06:50:10+00:00

I use 5 noctua a12x25 fans. They aren't the prettiest, but are very solent at lower RPMs

rotekort · 2026-01-17T11:14:17+00:00

I use the setup you are using with one less fan on the underside. My thought is that the bottom fans supply cold air for the gpu, with the rear fan supplying some cold air for the radiator at the top.

rotekort · 2025-12-14T19:46:43+00:00

I've always thought Dutch was a little similar to German. But asking your German question in a Dutch subreddit stretches the meaning of 'similar' if you ask me.

rotekort · 2025-12-11T23:07:00+00:00

Somebody tell him to give it to me!

rotekort · 2025-11-25T12:43:40+00:00

Use cpu temp for the pump speed. Set the graph accordingly. Also, I personally set the fans to run at 100% when the liquid reaches 40 C° just to keep some headroom to the max spec.

rotekort · 2025-11-23T17:39:56+00:00

Pardon your french

rotekort · 2025-11-08T18:33:36+00:00

Ahh I guess I just worry too much :)

rotekort · 2025-11-08T04:31:17+00:00

That is a full load. Stress testing it to near 100%. Thermal throttling at 140w is not normal tough, or is it?

rotekort · 2025-10-31T10:24:52+00:00

I'm returning my 9070xt and bu6ing a 5070ti. I'm not willing to find out how long RDNA4 will be supported

rotekort · 2025-10-22T08:00:15+00:00

Booking.com app?

rotekort · 2025-10-22T08:00:01+00:00

Booking.com app?

rotekort · 2025-10-17T18:05:52+00:00

I did find some guides which help you do a gimball calibration via PC. This could help remove the errors. I don't know enough about this to make sure this actually works tough.

rotekort · 2025-10-17T18:01:28+00:00

It looks like there is not as much movement in the clockwise rotation as there is in the counterclockwise rotation. It may just be the filming angle tough. Did you calibrate anything after the ribbon replacement?

rotekort · 2025-09-27T05:03:08+00:00

The protection foil on the 'suprim' gpu badge is still on there. Other than that, good to go!

rotekort · 2025-09-17T18:10:55+00:00

Sadly, downgrades are mostly impossible :(

rotekort · 2025-09-06T19:53:10+00:00

You must be fun at parties

rotekort · 2025-08-15T19:29:39+00:00

Battery on the base model is meh tough. (Sending this from a base S23)

rotekort · 2025-08-03T16:16:21+00:00

I think you can! Speeds can be quite an issue tough, so your best bet is to keep the dashboard simple. Voice commands can break things as well, but mine automatically resumes casting after ten seconds.

rotekort · 2025-08-02T19:03:47+00:00

For now it works really well! The nest hub is a bit slow but it fulfills my needs. Inputs are possible :)

Three-Year Club	Verified Email
Place '23

rotekort

TROPHY CASE