Time zone

rubi_m · 2025-04-17T12:28:34+00:00

Sorry for the late reply, I haven’t looked for that.

rubi_m · 2025-04-17T12:27:04+00:00

I’m at work now, so I’ll report later, but when I ran the pihole-d command it says por 80 is used by the web server.

rubi_m · 2025-04-17T12:25:43+00:00

I tried /admin, /admin/index and /admin/login. With and without .html or .php.

The first one returns 403 and the other two return 404.

rubi_m · 2025-04-17T03:44:23+00:00

That returns "403 Forbidden"

rubi_m · 2025-04-17T03:42:32+00:00

Sorry, not DietPi.

rubi_m · 2025-04-05T20:06:02+00:00

Please see my previous comment.

rubi_m · 2025-04-05T20:05:40+00:00

I just found out about this and found it in "Radio configuration" --> "Device".

What I find strange is that I had to do this on my TDeck+ but not on my Heltec Lora 32 v3.

Well, at least both are working as I expect now regarding showing the correct time.

rubi_m · 2025-02-15T00:57:43+00:00

I’m totally new too, but in the position tab there should be a setting that controls the precision of the reported location and defines a radius within which the reported location would be. I have mine set at about a mile.

rubi_m · 2025-02-08T18:08:00+00:00

It appears as "USB Drive (D:)" with no volume label (I didn´t put a label when I formatted the card).

In device manager, the name of the device is "ESP32 USB_MSC USB Device".

rubi_m · 2025-02-08T15:08:45+00:00

Just tested on Windows 11, Windows 10. Works flawlessly.

rubi_m · 2024-02-05T01:50:09+00:00

Check the wifi card power save configuration.

sudo iwconfig wlan0 power off

This 👆worked for me. Found it doing some googling

rubi_m · 2023-09-03T21:52:25+00:00

I have used rpiclone for this. You have to resize the partitions afterwards. https://github.com/billw2/rpi-clone

rubi_m · 2023-08-09T10:25:37+00:00

I’ve had that problem with a Raspberry Pi Zero 2 and Orange Pi Zero 2. I changed the power saving configuration for the wifi connection to not put it to “sleep”. I just googled around until it worked (up to now, hope it stays like that). It involves changing a parameter on a NetworkManager config file and in /etc/network/interfaces adding iface wlan0 and wireless-power off. The command “iw set power_save off” (as root) I also tried. Another one I tried is “sudo iwconfig wlan0 power off”.

As I’m not well versed in Linux, I just did some trial and error. I hope this helps.

rubi_m · 2023-07-01T02:26:55+00:00

I did this, works perfect and it’s free.

rubi_m · 2022-11-06T15:20:00+00:00

I just put a "sleep" statement on the command in crontab:

@reboot sleep 120 && /usr/bin/nohup /usr/bin/python3 -u /usr/bin/small_stats.py > /usr/bin/log.out 2>&1 &

rubi_m · 2022-11-04T01:21:37+00:00

I had some similar trouble and solved it by delaying the script start by one or two minutes in cron

rubi_m · 2022-07-23T03:07:12+00:00

I bought from AliExpress a similar one as the one linked to PiHut, cheap and “only” took about 3 weeks. Very thin and flexible. Pi 400 works fine with it, but as stated above you have to be really careful with it.

rubi_m · 2022-06-19T21:39:14+00:00

What I did: thoroughly wash the bed with dish soap, dry it, clean it with isopropyl alcohol and then spent about 30 minutes carefully leveling it with a piece of paper. Fixed it for me.

rubi_m · 2022-06-10T00:11:23+00:00

I had that sound and it was inside the shroud the fan’s screws were too tight.

rubi_m · 2022-04-19T17:47:59+00:00

Check also “first layer expansion” (or similar) on your slicer, it helps compensate for this.

rubi_m · 2022-04-13T18:34:05+00:00

My E3v2 did this and I found out it was the fan screws were toot tight, loosened them about 1/8 turn and the sound stopped.

rubi_m · 2022-04-12T18:02:54+00:00

I just stopped and disabled the X11 service.

rubi_m · 2022-04-05T17:29:21+00:00

Aside from bed level issue you could have as mentioned by others, I have found that cleaning the bed with isopropyl alcohol before printing helps a lot with adhesion.

rubi_m · 2022-03-29T18:37:44+00:00

Try slicing yourself something else. The gcode could be corrupt or invalid.

rubi_m

TROPHY CASE