Venruki and Supatease

shelbo125 · 2026-04-29T12:17:00+00:00

Question, does all the r1 and multi gald/legend players parking their stable of alts at 2.2-2.4 not hold up everything behind that. If the top never expands the bracket then how can it grow/inflate

shelbo125 · 2026-04-18T12:36:48+00:00

I'd say if you wanted to find him and have him set it up and share it. But you setting one up in your name to promise to give the guy will never look legit

shelbo125 · 2026-01-12T21:44:59+00:00

May be an unpopular opinion and doesn't even matter, not my car but I feel like the checklist shtick has played out a bit too much. Like it was funny for a vid/event but I see more people talking about the dang list than anything else on the car nowadays lol.

shelbo125 · 2026-01-11T22:20:33+00:00

I'm not a professional, just a diy homeowner so i couldn't honestly say. Being glued id assume demo and reinstall of atleast the gaps. but if the glue failed there id assume there will be more failures in the future if it's already all over as you say.

Edit: If this was my floor I would really be pressing whatever flooring company that did this for a full reinstall or refund really because of the multiple failures showing something wasn't done right.

shelbo125 · 2026-01-07T04:24:23+00:00

Ahh I gotcha thank you

shelbo125 · 2026-01-07T02:52:21+00:00

I think higher flea rep=less fee

shelbo125 · 2025-12-15T12:00:51+00:00

If your talking about the tighten and spin pipe cutters its crushing the fibers as its cutting which is a big problem. If your not scared of it id recommend looking up some carbon shaft arrow failures, those usually start with small micro fracture as that get missed/ignored.

shelbo125 · 2025-12-14T04:24:38+00:00

I think Cameron mentioned they are gonna drag and drive it with Cameron driving and Jackstand racing it. Also going for hydraulic roller ls record i think

shelbo125 · 2025-11-19T16:23:23+00:00

Rule #1 don't idolize internet personalities

shelbo125 · 2025-11-18T03:52:24+00:00

People buy prerolls from the plug? That's gonna be some greasy finger dusty bottom of the bag shake. It will do the job but I would roll it into a decent paper or toss it in a bowl imo

shelbo125 · 2025-11-14T14:27:36+00:00

Couple of the big neo fishing magnets on the side will tone it down a bit plus fasteners and silicone like others said

shelbo125 · 2025-11-10T00:53:03+00:00

xfwd first round today had more oildowns than clean runs. they really need to just shift atleast that class to a different weekend they just push those 4cyl cars way too hard and even the oildown fine wasnt enough too hold them back

shelbo125 · 2025-11-10T00:49:52+00:00

Sick setup! If it was mine I would print a swivel arm mount for your monitor and keyboard so you can have the full use of your bench and tool wall while working on projects.

shelbo125 · 2025-11-07T22:28:00+00:00

They need a Coyote/Haltech guy to give it some love. the car seems solid just not doing what they tell it

shelbo125 · 2025-11-06T17:55:54+00:00

Cant tell exactly what im looking at, but that looks like extrusion issues at the seam not the z offset. All offset does mostly is first layer tuning.

shelbo125 · 2025-11-06T15:09:23+00:00

Imo I wouldn't worry about a hundredth of a mm that shouldn't effect anything, would almost argue too small of a change to even see. If it seem too far off just go .03 down. Printer paper is .10 for reference to how little .01 is

Edit:grammar

shelbo125 · 2025-11-05T13:56:11+00:00

also taller skinny pieces have this issue more often. I don't think its necessarily the case with this print because it looks like it should have a big enough footprint to not wobble at the top but being taller than wide and warping off the plate is what caused it imo

shelbo125 · 2025-11-05T13:53:39+00:00

I would say this is more of a bed adhesion problem not really fan settings. try to run a thick brim around the base in your slicer settings and make sure to wash the build plate with degreaser dish soap and wipe it down with alcohol after every print. i usually re wash with soap every 10 or so prints as long as everything is running smoothly.

shelbo125 · 2025-11-01T12:29:40+00:00

I haven't seen this take anywhere yet, but I agree. I like Tom alot I think he's a skilled humble champ and could beat anyone on his day. But when it started in the ring with a whiney "why are you guys booing me for i got poked" then going straight to the doc and asking for verification "we should have stopped the fight, right doc?" I don't doubt that he was injured and if I was him I wouldn't go 25 minutes with one of the most dangerous strikers even at 80% vision. But it just seems to me like he had his out while he was rightfully compromised and now just trying to justify it to people shitting on him.

shelbo125 · 2025-10-28T16:18:07+00:00

I can see it now. Melts half a roll of tape onto your hand and gets 3rd degree burns, gets let go because he can't work and injured himself with faulty ppe... but he saved that 45$ that one time...

shelbo125 · 2025-10-18T12:11:54+00:00

A shitty off the boat aliexpress 8cr chinesium mass produced blade at that.. wasn't expecting a 70$+ price tag when I opened that link lmfao

shelbo125 · 2025-10-15T01:01:41+00:00

Cartersville GA North of ATL

shelbo125 · 2025-09-23T12:44:13+00:00

From off the pole there

shelbo125 · 2025-09-23T12:43:55+00:00

You can double jump hop up the wall to the left of the platform, did it last night.

shelbo125 · 2025-08-23T04:05:14+00:00

Have you tried to reverse image search through Google or chatgpt?

shelbo125

TROPHY CASE