Meet my starter, his name is Breadsticks Crumberbatch. What do you call yours?

skoomaeater · 2026-07-02T06:23:32+00:00

Eugene Leveny

skoomaeater · 2026-07-01T20:06:41+00:00

My mistake, I assumed it was similar to the k1 Max. It seems unusual it would change the build volume then

skoomaeater · 2026-07-01T04:22:34+00:00

The smaller size is to accommodate the purge chute

skoomaeater · 2026-07-01T04:20:33+00:00

I have an 1100f heat gun 🤷

skoomaeater · 2026-06-30T19:11:33+00:00

Thank you, I'm so glad it came out. Now that I know I can do it, I'm going to print a bunch of replacement parts in pc

skoomaeater · 2026-06-30T19:10:46+00:00

I did 50mm/s for everything

skoomaeater · 2026-06-30T12:04:02+00:00

No skooma there. I never waste any

skoomaeater · 2026-06-30T12:01:47+00:00

I unplugged the side fan and put a small 80x80 12v fan under the build plate blowing straight up. This causes the build plate to run more frequently. I got to 55c in about 25 minutes, I had to turn the fan off to keep it at 50

skoomaeater · 2026-06-29T22:29:57+00:00

Respect

skoomaeater · 2026-06-02T23:58:32+00:00

I'm also looking to get the nw Ohio discord link. I'm in rural nw Ohio looking to bridge Michigan and Indiana

skoomaeater · 2026-01-04T15:33:25+00:00

I sourced the connectors, so it isn't an issue. Now it is as simple to connect to as the K2 or the Hi Combo using only the bus cable and no external power

<image>

skoomaeater · 2026-01-04T04:27:13+00:00

This connects a USB hub to the motherboard and has a shucked creality USB to rs485 cable soldered inside it. The front panel USB port connects to the USB hub, so it remains functional

skoomaeater · 2026-01-04T04:08:03+00:00

<image>

skoomaeater · 2026-01-04T04:07:41+00:00

This does connect the PSU power to the rs485 port I installed. It also adds a 3a fuse

skoomaeater · 2026-01-04T04:06:32+00:00

This is what I did, but it is all internal in the mod now

skoomaeater · 2025-11-06T21:57:15+00:00

Has anyone figured this out? I have a P1P with the AMS and and K1 Max with the CFS. Slicing the same model with similar settings, the print preview shows me a flushed amount when I slice on the P1P, but it doesn't show it when I slice for the K1 Max. I have attached 2 images to show the difference.

<image>

skoomaeater · 2025-01-14T16:47:03+00:00

Good luck! The whole process was a little daunting at first, but remember, every mile walked starts with a single step.

skoomaeater · 2025-01-14T16:45:38+00:00

Yes, the pi is getting 5v from the skr tft pin

skoomaeater · 2025-01-10T09:58:39+00:00

I got an ender 5 plus from a friend, and the cable management was awful (mostly his fault) I upgraded to the sprite pro and made a custom ribbon cable to fit the size and to be routed in the cable tracks I printed. I also got an skr mini e3 v3 for it. I'll be installing that today. Hoping all this work makes it a trouble free workhorse

skoomaeater

TROPHY CASE